background image

2

Safety precautions

Make sure to follow the precautions described below to avoid injury or unnecessary property loss to anybody. 

The safety precautions are classified according to the degree of harm or damage caused by misuse.

Examples of symbols:

This symbol means 
“reminding”. 

This symbol means 
“forbidden”.

This symbol means necessary 
“instructions”. 

 

In case of any abnormality or machine 

failure, stop using the machine 

immediately, turn off the power switch, 

and unplug the power plug from the 
power socket

Failure  could  cause  smoke,  fire,  or  electric 

shocks

[Example of abnormalities]

•  Abnormal sound or smell

Please stop using the product and contact the 

store where the product was purchased from 

or the Iris Call center

 

Warning

The symbol means matters which may lead to death 

or serious injury during faulty operation.

Prohibited

 

Do  not  spray  liquids  onto  this  product, 

such as insecticides, hair care products, 

or lubricating oil, etc

 

Do  not  use  the  machine  to  vacuum 

flammable  or  combustible  substances 

(such  as  kerosene,  gasoline,  thinner, 

copy machine toner, etc.)

 

Do  not  use  the  machine  to  vacuum  oil, 

smoke or steam

 

Do  not  use  the  machine  to  vacuum  dry 

dust

 

Do not use the machine near combustible 

substances,  lit  cigarettes  or  incense 

sticks

Failure could cause a fire.

Do not 

disassemble

 

Do not disassemble, repair, or modify the 
machine

Failure  could  cause  a  fire,  electric  shocks  or 

injury. For repair, please contact the store where 

the product was purchased from or contact the 

call center to arrange for repair.

Correctly use the power plug and power cord

Be sure to

 

Please  periodically  clean  the  dust  from 

the power plug

The accumulation of dust could cause fire or 

electric shocks due to insulation faults.

 

Insert  the  power  plug  into  the  socket 

thoroughly

Otherwise it could cause fire or electric shocks 

due to short circuits.

 

Be  sure  to  unplug  the  power  plug  from 

the socket before repairing, checking or 

moving

Failure could cause electric shocks or injury.

 

Do not plug or unplug the power plug 
with wet hands

Failure  could  cause  electric  shocks,  burn,  or 

injury.

Prohibited

 

Do not let infants lick the plug

Doing  so  could  cause  an  injury  or  electric 
shocks.

 

Do  not  power  on  the  product  when  the 
power cords are bundled

Doing so could cause empyrosis or fire due to 

overheating. Be sure to extend the power cord 

for use.

 

Do not damage the power cord

 

Do not pull the power cord while moving 

and storing

Do  not  damage  or  press  the  power  cord, 

forcibly bend or stretch the power cord, twist, 

place heavy objects on or modify the power 

cord.

Doing so could cause fire or electric shocks 

due to the damaged power cord.

 

Do  not  use  a  damaged  power  cord  or 
power plug, or a loose socket

Doing so could cause a fire or electric shocks 

due  to  a  short-circuit.  If  the  power  cord  is 

damaged,  please  contact  the  call  center  to 

arrange for repair.

 

Do not use an 
incorrectly rated 

electrical outlet 

socket or 

extension cord

Failure could cause 

a fire.

 

Do  not  use  an AC  power  source  other 

than 220V

~

Doing so could cause a fire or electric shocks.

Prohibited

Содержание RNS-300
















Отзывы: