IQ PBX600 Скачать руководство пользователя страница 75

Страница: 75 / 134

www.yeastar.com

Page 75

IQ PBX 600 User Manual

Note:

If you would like to use G.729, please enter your license.

Figure 3.5.5

3.5.6 Voicemail Settings

General Voicemail Settings

Message Options

·Max Messages per Folder

Set the maximum number of messages that can be stored in a single voicemail
box.

·Max Message Time

Set the maximum length of a single voicemail message.

·Min Message Time

Set the minimum length of a single voicemail message. Messages below this
threshold will be automatically deleted.

·Ask Caller to Dial 5

If this option is set, the caller will be prompted to press 5 before leaving a
message.

·Operator Breakout from Voicemail

If this option is set, the caller can jump out of the voicemail and go to the
destination (IVR) you set by dialing “0”.

Greeting Settings

Busy Prompt

Greeting played when the extension called is busy.
Skip greeting: Do not play a greeting.
Play busy greeting: play the extension busy greeting.

Содержание PBX600







































































































































Результаты поиска

Содержание PBX600

Отзывы:

Похожие инструкции для PBX600

Бренды по названию

Популярные бренды

IQ PBX600, Руководство пользователя

Результаты поиска

Содержание PBX600

Отзывы:

Похожие инструкции для PBX600

Бренды по названию

Популярные бренды