IQ PBX600 Скачать руководство пользователя страница 10

Страница: 10 / 134

www.yeastar.com

Page 10

IQ PBX 600 User Manual

Status

Idle

: The port is idle.

Busy

: The port is in use.

Disconnected

: The port hasn’t connected the PSTN line.

More detail message, please refer to the LED identifying of front panel.

GSM Trunk

Status

Idle

: The port is idle.

Busy

: The port is in use.

Signal

: No signal.
: Poor.
: Average.
: Good.

: Excellent.

BRI Trunk

Status

: The ports connect correctly.

Disconnected

: The port hasn’t connected the PSTN line.

Service Provider

Status

: Succeed registration, trunk is ready for use.

Unreachable

: The trunk is unreachable.

Failed

: Trunk registration failed.

3.3 Basic

3.3.1 Extension

Extension has two types: Analog extensions (FXS) and VOIP extensions (SIP
extension or IAX extension).

Содержание PBX600







































































































































Результаты поиска

Содержание PBX600

Отзывы:

Похожие инструкции для PBX600

Бренды по названию

Популярные бренды

IQ PBX600, Руководство пользователя

Результаты поиска

Содержание PBX600

Отзывы:

Похожие инструкции для PBX600

Бренды по названию

Популярные бренды