IQ PBX600 Скачать руководство пользователя страница 69

Страница: 69 / 134

www.yeastar.com

Page 69

IQ PBX 600 User Manual

Maximum duration (in seconds) of a SIP registration . Default is 3600 seconds.

·Min Registration/Subscription Time

Minimum duration (in seconds) of a SIP registration . Default is 60 seconds.

·Default Incoming/Outgoing Registration Time

Default Incoming/Outgoing Registration Time: Default duration (in seconds)
of incoming/outgoing registration.

·Register Attempts

The number of SIP REGISTER messages to send to a SIP Registrar before giving
up. Default is 8 times.

·Register Timeout

Number of seconds to wait for a response from a SIP Registrar before timed out .
Default is 20 seconds.

·Calling Channel Codec Priority

Once enabled, when dialing out via SIP/SPS trunks, the codec of calling channel
will be selected in preference. If not, IQPBX600 will follow the priority in your
SIP/SPS trunks.

·Video Support

Support for SIP video or no. Default is yes.

·Max Bit Rate

Configure the max bit rate for video stream. The default: 384kb/s

·DNS SRV Look Up

Please enable this option when your SIP trunk contains more than one IP
address.

·User Agent

To change the user agent parameter of asterisk, the default is ‘IQPBX600’, you
should change it if needed.

NAT

Note

: Configuration of this section is only required when using remote

extensions.

·Enable STUN

STUN (Simple Traversal of UDP through NATs) is a protocol for assisting devices
behind a NAT firewall or router with their packet routing.

Содержание PBX600







































































































































Результаты поиска

Содержание PBX600

Отзывы:

Похожие инструкции для PBX600

Бренды по названию

Популярные бренды

IQ PBX600, Руководство пользователя

Результаты поиска

Содержание PBX600

Отзывы:

Похожие инструкции для PBX600

Бренды по названию

Популярные бренды