IQ Power Tools iQMS362-230V CE Скачать руководство пользователя

Страница: 25 / 41

iQMS362 CE

Operator’s Manual

888-274-7744

www.iqpowertools.com

gli

, E

SAFETY

WORK AREA SAFETY

• Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

• People and animals can distract you causing

you to lose control of the machine. For this

reason, always remain concentrated and

focused on the task.

• Do not use the machine in bad weather, such

as dense fog, heavy rain, strong wind, intense

cold, etc.

• Never start to work with the machine

before the working area is clear and you

have a stable work surface.

PERSONAL SAFETY

Never use the machine if you are fatigued, while under

the influence of alcohol or drugs, medication or anything

that could affect your vision, alertness, coordination

or judgement.

• Check that no tools or other objects have been

left lying on the machine.

• Never allow anyone else to use the machine

without proper training.

• Always shut off the machine during longer

work breaks.

• Never work alone, always ensure there is

another person close at hand.

• Learn how to use the machine and its controls

safely and learn to how to stop quickly.

Also learn to recognize the safety decals.

• Keep handles dry, clean and free from

oil and grease.

• Do not overreach. Keep proper footing and

balance at all times.

• Never stand on the machine.

Stand upright. Keep

distance between your

face and the cutting blade.

Place both hands on the

work piece as far away

from the cutting blade as

possible. If plunge function

is used, place one hand on

the cutting handle.

MACHINE USE AND CARE

• This machine is designed and intended for

cutting concrete and stone. All other

use is improper.

• Experience is very important when running

the machine. A skilled worker is highly

recommended.

• The machine is intended for use in industrial

applications by experienced operators.

• Check that the machine is assembled correctly

and do not show any signs of damage.

• Always perform daily maintenance before

starting the machine. See instructions in the

section “Maintenance”.

• Do not overload the machine. Overloading

can damage the machine.

• The blade shall be intended for the

material to be cut.

• If you are uncertain of what blade to use

contact your local service dealer.

• Keep tools sharp and clean in order

to enable safer work.

• Keep all parts in good working order and ensure

that all fixtures are properly tightened. Replace

all worn or damaged decals.

• Never leave the machine unsupervised with

the motor running.

• Feed the work piece against the rotation of

the blade only!

• Observe care when lifting. You are handling

heavy parts, which imply the risk of pinch

injuries or other injuries.

• For safety reasons each damaged (cracked)

blade has to be replaced.

• Prevent any contact with the rotating tool.

9.3

Содержание iQMS362-230V CE










































Результаты поиска

Содержание iQMS362-230V CE

Отзывы:

Похожие инструкции для iQMS362-230V CE

Бренды по названию

Популярные бренды

IQ Power Tools iQMS362-230V CE, Руководство оператора

Результаты поиска

Содержание iQMS362-230V CE

Отзывы:

Похожие инструкции для iQMS362-230V CE

Бренды по названию

Популярные бренды