IQ Power Tools iQMS362-230V CE страница 12 Скачать руководство пользователя

Страница: 12 / 41

iQMS362 CE

Operator’s Manual

888-274-7744

www.iqpowertools.com

gli

, E

General

This section describes the machine

’

s safety equipment,

its purpose, and how checks and maintenance should be

carried out to ensure that it operates correctly.

WARNING!

NEVER USE A MACHINE THAT HAS

FAULTY SAFETY EQUIPMENT

BLADE GUARD

The blade guard is designed to prevent parts of

the blade or cutting fragments from being thrown

towards the user.

CHECKING THE BLADE GUARD

Check that the guard over the blade is not cracked or

damaged in any other way. Replace when damaged.

DUST GUARD

The dust guard is designed to prevent dust being pulled

up from the backside of the blade. The dust guard should

be inspected periodically for damage. The dust guard

should move freely sliding up and over cutting material.

NEVER USE THE MACHINE

WITHOUT A GUARD NOR WITH A

DEFECTIVE GUARD. ALWAYS CHECK THAT THE GUARD IS

CORRECTLY FITTED BEFORE STARTING THE MACHINE.

IT IS NOT PERMITTED TO EXPOSE THE BLADE MORE THAN

180 DEGREES WITHOUT PROTECTION.

WARNING!

SHUT DOWN THE MACHINE AND

DISCONNECT THE POWER PLUG.

MACHINE’S SAFETY EQUIPMENT

MACHINE POWER SWITCH

To start the machine press the green button (A) on the

switch. NOTE: Machine is protected by the GFI switch

reset button (D). This must be pressed each time

machine is connected to power.

To stop the machine, press the red button (B). NOTE:

Machine is protected by a built-in thermal circuit

breaker (C).

Defective switches should be replaced by an authorized

service workshop.

LOCKING KNOB, ROLLING TABLE

The locking knob is used to lock the rolling table in place

when in transit. Be sure to lock rolling table before

transit to avoid injury.

5.1

Blade Guard

Dust Guard

Содержание iQMS362-230V CE










































Результаты поиска

Содержание iQMS362-230V CE

Отзывы:

Похожие инструкции для iQMS362-230V CE

Бренды по названию

Популярные бренды

IQ Power Tools iQMS362-230V CE, Руководство оператора

Результаты поиска

Содержание iQMS362-230V CE

Отзывы:

Похожие инструкции для iQMS362-230V CE

Бренды по названию

Популярные бренды