iPECS LIP-7024LD Скачать руководство пользователя

Страница: 48 / 58

LIP-7024LD

User

Guide

OPERATION

To set the Wake Up Alarm clock:

•

Press

TRANS

PGM

•

Dial the Station User Program code 41,

•

Dial 2-digit hour and minute for alerting,

•

For a daily (repeating alarm), dial #,

•

Press

HOLD

SAVE

To erase Wake-Up:

•

Press

TRANS

PGM

•

Dial the Station User Program code 42,

•

Press

HOLD

SAVE

9.5 Alarm/Door

Bell

The system can monitor external Alarm or Door Bell contacts:

Alarm Monitor—should the external contact activate, a unique Alarm

Ring signal and LCD display may be received. To restart the monitor

circuit, the external contacts must be deactivated and the Alarm Ring

signal terminated.

Door Bell—a unique Door Bell Ring (single tone burst) may be received

each time the external contact is activated. A system contact also can

be assigned to act as a Door Open contact.

OPERATION

To terminate the Alarm signal:

•

Dial 565.

To activate the Door Open contacts:

•

Lift the handset,

•

Dial Door Open code, #* and contact number 1-4.

NOTE—Contacts 3 & 4 are only available in the iPECS -300 & 600.

9.6 Power

Fail

Transfer

When AC power to the system fails, back-up operation may be provided

with back-up batteries or Power Fail Transfer (PFT). When battery

back-up is provided the station will operate normally. When PFT is

implemented, an SLT is connected to a CO line by the system. This

SLT can be used as any normal SLT, providing service while power is

out.

9.7

System Voice Memo

The integrated Voice Mail modules incorporate several Voice Memos to

provide Station Users with general information such as station number,

４４

Содержание LIP-7024LD



























































Результаты поиска

Содержание LIP-7024LD

Отзывы:

Похожие инструкции для LIP-7024LD

Бренды по названию

Популярные бренды

iPECS LIP-7024LD, Руководство пользователя

Результаты поиска

Содержание LIP-7024LD

Отзывы:

Похожие инструкции для LIP-7024LD

Бренды по названию

Популярные бренды