iPECS iPECS-LIK Скачать руководство пользователя страница 246

Страница: 246 / 447

iPECS-LIK
Feature Description & Operation Manual

Issue 6.0d1

233

4. Dial 2-digit hour and 2-digit minute for alerting.

For a daily (repeating alarm), dial “#”.

6. Hook flash, conformation tone is provided.

To stop the alarm notification

1. Lift the handset.

To erase Wake-Up

1. Lift the handset.

Dial “562”, the SLT Programming code, confirmation tone is heard.

Dial “42”, the erase Wake-up code.

4. Hook flash, a conformation tone is provided.

Conditions

1. In cases where a remote device is installed, the time display in the remote terminal

is adjusted by the Device Zone assignment. Thus, the Wake-up alarm time is
based on the time displayed on the phone and not the system time.

2. When receiving a wake up signal, lifting the handset will return MOH.

3. The Wake-up alarm Ring signal is 30 seconds On/90 seconds Off repeated 3 times.

If no action is taken by the user, the ring signal is given to the Attendant with a
display designating the station number that did not respond.

4. Time (hh:mm) must be entered in the Military 24-hour format.

5. The daily alarm will reset and repeat each day until erased (cancelled). The One-

time alarm will reset and cancel automatically.

6. If you set PGM 114-B24-B6 for WakeUp Announce, you can hear the system

announce number when you register wake-up.

Programming



PGM114-B24-B6 : WAKEUP ANNC(0-70)

Related Features

Hardware

Содержание iPECS-LIK
































































































































































































































































































































































































































































Результаты поиска

Содержание iPECS-LIK

Отзывы:

Похожие инструкции для iPECS-LIK

Бренды по названию

Популярные бренды

iPECS iPECS-LIK, Описание функций и эксплуатация

Результаты поиска

Содержание iPECS-LIK

Отзывы:

Похожие инструкции для iPECS-LIK

Бренды по названию

Популярные бренды