English
- 26 -
ADVICE ON USING DETERGENTS
Warning
This cleaner has been designed for use with the detergents
supplied or recommended by the manufacturer.
The use of other detergents or chemicals may influence the
safety of the cleaner.
1
)
For environmental compatibility
, we recommend a reaso-
nable use of detergents, according to the instructions on the
pack.
2
) From the range of recommended products, choose the
one most suited to the washing job to be done and dilute it
with water according to the instructions on the pack or in the
catalogue of the detergents most suited for the type of hot or
cold water cleaner.
3
) Ask your dealer for the detergents catalogue.
OPERATING PHASES FOR CORRECT CLEANING WITH
DETERGENTS
1
) Prepare the solution of detergent at the concentration
most suitable for the type of dirt and the surface that is to be
washed.
2
) Switch on the water cleaner. Select the detergent (1 or 2) with
the selector (C, fig. 7). Turn the relevant detergent flow regulator
anti-clockwise; (L) for detergent 1 or (M) for detergent 2 (fig.
7)
Spray detergent on to the surface to wash, proceeding from
the bottom upwards.
Leave the detergent react for a few minutes.
3
) Turn the detergent selector (C, fig. 7) back to position 0. Turn
the detergent flow regulators clockwise to stop detergent flow.
3
) Rinse the whole surface well from top to bottom with hot or
cold water at high pressure.
4
) After using with detergent, flush out the intake circuit; place
the detergent suction hose (fig. 8) in a tank of clean water and
let the pump run for 1 minute with the dosing tap turned fully
on and the lance in detergent delivery condition.
Repeat the operation with the detergent selector set first to
position 1 and then to position 2.
MAINTENANCE
ONLY THE OPERATIONS AUTHORIZED IN THIS IN-
STRUCTIONS MANUAL MAY BE CARRIED OUT BY
THE USER.
ALL OTHER OPERATIONS ARE FORBIDDEN.
Danger
For maintenance of the boiler, high pressure pump, the electrical
parts and all parts with a safety function, you must apply to our
Technical service centre.
The manufacturer is not liable in case of tampering, changes, in-
correct repairs or maintenance carried out on the machine by a
third person not provided with the manufacturer’s authorization.
All documents pertaining to the repair and planned service
interventions, as well as any certificates concerning the device
installation according to the laws in force (in compliance with the
provisions of the IEC 60364-1 standard) must be kept carefully
by the user, together with the Instructions Manual.
Periodically, at least once a year, have the safety devices and
the rated values checked at one of our technical service centres.
Danger
Disconnect the water cleaner from the mains electricity sup-
ply via the omnipolar switch or by unplugging the plug from
the socket and close the water supply tap (see chapters on
connecting to the electricity and water mains
)
before carrying
out any maintenance jobs. Once maintenance has been
completed, ensure that the closing panels have been correctly
reassembled and anchored with the screws provided before
reconnecting the cleaner to the mains.
Failure to do so may cause a risk of electric shock.
PRECAUTIONS AGAINST FROST
The cleaner must not be exposed to frost.
If the cleaner is left in premises where it is exposed to frost,
when work is over or for storage, antifreeze must be used to
prevent serious damage to the hydraulic circuit.
!
!
REMOTE CONTROL (Optional Accessory)
AAll models are designed to be equipped with a remote control,
supplied as an optional accessory. The control panel features:
A) On/off switch.
B) Heating system switch.
C) Detergent selector.
The remote control operates over distances of up to 30 metres.
1) Switch the high pressure cleaner on by turning the on/off
switch to pos. “l”. The switch on the high pressure cleaner must
be in pos. "I", with the indicator light "N" on.
2) To operate the high pressure cleaner with hot water, turn the
heating system switch B to pos. I.
The temperature can only be adjusted on the high pressure
cleaner.
!
3) Select the type of product to be used ("1" or "2") using the
selector C).
The product can only be selected on the high pressure cleaner.
Any faults are only signalled on the high pressure cleaner
control panel.
If the high pressure cleaner stops, move the on/off switch on
the remote control to pos. "O", turn the main switch "A" on the
pressure cleaner to pos. "0" and then back to pos. "I". Move the
on/off switch on the remote control back to pos. "I".
