IP-COM F1226P Скачать руководство пользователя страница 58

Страница: 58 / 58

Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

NOTE:

(1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized

modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a

shielded RJ45 cable

Disclaimer:

This equipment is an industry class product instead of an end-user device. It may cause harmful

interference to radio communications. If this equipment does cause harmful interference to radio communications,

which can be determined by turning the equipment off and on, the user may need to take some measures to correct

the interference.

Содержание F1226P



























































Результаты поиска

Содержание F1226P

Отзывы:

Похожие инструкции для F1226P

Бренды по названию

Популярные бренды

IP-COM F1226P, Руководство пользователя

Результаты поиска

Содержание F1226P

Отзывы:

Похожие инструкции для F1226P

Бренды по названию

Популярные бренды