IOtech Digital HS Скачать руководство пользователя страница 39

Страница: 39 / 58

fast as the slowest listener. The Digital488HS/32 is capable of transmitting bus data
at a rate greater than 1,000,000 bytes per second.

3.3 Serial Polling

The Digital488HS/32 can provide internal and external status in addition to
generating requests for service via the SRQ IEEE 488 control line. The following
shows the status bit positions contained within the Serial Poll Byte Status Register.

rsv

SB2

SB1

FULL

EMPTY

DIO8

DIO7

DIO6

DIO5

DIO4

DIO3

DIO2

DIO1

Serial Poll Byte
Bit Assignments

These status bits include:

DIO1

FULL

The input port is Full.
Data may be read from the input port.

DIO2

EMPTY

The output port is Empty.
Data may be written to the output port.

DIO3

SB1

External Status Bit #1 input.
Level Sensitive Bit. Rising edge SRQ generating if
enabled.

DIO4

SB2

External Status Bit #2 input.
Level Sensitive Bit. Rising edge SRQ generating if
enabled.

DIO5

Not Used

Always 0.

DIO6

Not Used

Always 0.

DIO7

rsv

Reserved Bit. Indicates the Digital488HS/32 caused

the SRQ.
DIO8

Not Used

Always 0.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание Digital HS



























































Результаты поиска

Содержание Digital HS

Отзывы:

Бренды по названию

Популярные бренды

IOtech Digital HS, Руководство пользователя

Результаты поиска

Содержание Digital HS

Отзывы:

Бренды по названию

Популярные бренды