manualshive.com logo in svg

INVISIBLE FENCE Safe Dog Monitor, Инструкция по установке и обучению

Поделиться
Скачать
INVISIBLE FENCE Safe Dog Monitor Скачать руководство пользователя страница 14

- DRAFT - 

Rev. 1.0 JAB 

 

 

14 

G:\PCTEST LAB\2006 Reports\TRP\Safe Dog Monitor - Part 68\TCB Documents\KZ3-050808 manual.doc 
Need Part Number 

 

5.1.3 Registration – After Installation 

If “kitting” of customer system components is not done, the registration of the Safe Dog Monitor 
must be done after installation.  During the installation, the serial number of the Dialer must be 
recorded for entry into the Safe Dog Monitor warranty database.  This can be done on the installation 
contract of installation checklist. 
 
When the paperwork is returned to the office, the information can be entered into the Safe Dog 
Monitor warranty database.  This site can be accessed at 

[enter site address]

.  A user name and 

password is required to access this protected site. 
 
A Safe Dog Monitor section is available to each Invisible Fence Brand Dealer.  This section allows 
the Dealer to register the Safe Dog Monitor and other system components (transmitter, receiver, etc.) 
to a specific customer.  
 
For detailed directions on registering the Safe Dog Monitor, please refer to the Safe Dog Monitor 
Registration Manual. 
 

Содержание Safe Dog Monitor
















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды