background image

SECTION 3—SAFETY INSPECTION/TROUBLESHOOTING

Part No. 1110546

17

Tracer® EX2

CAUTION

DO NOT overtighten hardware attaching to the frame. This could cause damage to the frame tubing.

Suggested Maintenance Procedures

1.

Before

 

using

 

your

 

wheelchair,

 

make

 

sure

 

all

 

nuts

 

and

 

bolts

 

are

 

tight.

 

Check

 

all

 

parts

 

for

 

damage

 

or

 

wear

 

and

 

replace.

 

Check

 

all

 

parts

 

for

 

proper

 

adjustment.

CAUTION

As with any vehicle, the rear wheels, casters and tires should be checked periodically for cracks 

and wear, and should be replaced if damaged.

2.

The

 

rear

 

wheels,

 

casters

 

and

 

tires

 

should

 

be

 

checked

 

periodically

 

for

 

cracks

 

and

 

wear,

 

and

 

should

 

be

 

replaced

 

by

 

a

 

qualified

 

technician

 

if

 

damaged.

NOTE:

 

Tire

 

wear

 

is

 

excessive

 

if:

Pneumatic

 

Tires

 ‐ 

there

 

is

 

missing

 

tread

 

or

 

the

 

tires

 

are

 

bald.

Urethane

 

Tires

 ‐ 

there

 

are

 

cuts,

 

surface

 

defects

 

or

 

the

 

tires

 

are

 

loose

 

on

 

the

 

rims.

Rubber

 

Tires

 ‐ 

30%

 

or

 

more

 

of

 

the

 

tire

 

has

 

worn

 

away.

NOTE:

 

Invacare

 

recommends

 

that

 

tires

 

and

 

casters

 

be

 

replaced

 

every

 

five

 

years.

3.

Periodically

 

adjust

 

wheel

 

locks

 

in

 

correlation

 

to

 

tire

 

wear.

 

Refer

 

to

 

Adjusting

 

Patient

 

Operated

 

Wheel

 

Locks

 

on

 

page 36.

4.

Periodically

 

check

 

handrims

 

to

 

ensure

 

they

 

are

 

secured

 

to

 

the

 

rear

 

wheels.

 

If

 

loose,

 

have

 

them

 

tightened

 

by

 

a

 

qualified

 

technician.

5.

Periodically

 

check

 

caster

 

wheel

 

bearings

 

to

 

make

 

sure

 

they

 

are

 

clean

 

and

 

free

 

from

 

moisture.

 

Use

 

a

 

Teflon™

 

lubricant

 

if

 

necessary.

WARNING

When cleaning rear cane or hand grip areas use only a clean towel lightly dampened with cool 

water. Verify that grips are dry prior to use. Use of soap or ammonia based cleaning solutions 

will result in the hand grips sliding off the cane assembly. Failure to observe this warning may 

result in injury to the user or bystanders.

6.

Hand

 

grips

 

should

 

be

 

checked

 

monthly

 

for

 

wear/looseness/deterioration.

 

Clean

 

if

 

desired.

 

Replace

 

if

 

looseness

 

or

 

deterioration

 

is

 

found.

7.

Check

 

upholstery

 

for

 

sagging,

 

rips

 

or

 

tears.

Содержание TRACER EX2









































Отзывы: