Invacare Ranger II Storm R2 250-S Скачать руководство пользователя

Страница: 24 / 56

S
T
R
A
P

PROCEDURE 6

UPHOLSTERY/POSITIONING STRAP

L
S
T
E

Hex Bolts

(Apply Loctite

242 and torque

to 75-inch

pounds)

Locknuts

Back Upholstery

Washer

Phillips

Screw

Tie Wrap Mounting Holes

Washers

FIGURE 4 - REPLACING BACK UPHOLSTERY -

WHEELCHAIRS BUILT AFTER 10/2000

Back Cane

10. Use Loctite 242 on the hex bolts and torque into the

back canes to 75-inch pounds.

11. While holding the hex bolt, reinstall the locknut and

torque to 75-inch pounds.

12. Repeat STEP 11 for the other hex bolt and locknut.

13. Securely tighten the new back upholstery to the back

canes with the two (2) phillips screws and washers.

14. Secure the bottom of the new back upholstery to the

wheelchair frame with tie-wraps.

NOTE: Clean upholstery with warm DAMP cloth and
mild detergent to remove superficial soil.

WARNING

Laundering or moisture will reduce flame retar-
dation of the upholstery.

Wheelchairs Built After 10/2000
(FIGURE 4)

1. Flip the armrests up and out of the way. Refer to

USING/ADJUSTING FLIP BACK ARMRESTS in
PROCEDURE 5 of this manual.

2. Cut the tie-wraps that secure the bottom of the exist-

ing back upholstery to the wheelchair frame.

3. Remove the two (2) phillips screws and washers that

secure the existing back upholstery to the back canes.

4. Remove the two (2) hex bolts, washers and lock-

nuts that secure one (1) back cane to the wheelchair
frame.

NOTE: It is necessary to remove only one (1) back cane
to replace the back upholstery.

5. Pull the loose back cane out of the existing back

upholstery.

6. Pull the existing back upholstery up and over the

mounted back cane.

7. Install new back upholstery over mounted back cane.

8. Slide the loose top half of the back cane through the

new back upholstery.

9. Using the mounted back cane as a guide, reinstall

the two (2) hex bolts that secure the top half of the
back cane to the bottom half of the back cane.

NOTE: Make sure the back canes are mounted to the
same height.

WARNING

The top and bottom half of the back canes MUST
be tightened securely together BEFORE using the
wheelchair, otherwise injury or damage may oc-
cur. Use Loctite 242 on the hex bolts and torque to
75-inch pounds.

Содержание Ranger II Storm R2 250-S

























































Результаты поиска

Содержание Ranger II Storm R2 250-S

Отзывы:

Похожие инструкции для Ranger II Storm R2 250-S

Бренды по названию

Популярные бренды

Invacare Ranger II Storm R2 250-S, Руководство пользователя

Результаты поиска

Содержание Ranger II Storm R2 250-S

Отзывы:

Похожие инструкции для Ranger II Storm R2 250-S

Бренды по названию

Популярные бренды