Invacare Ranger II Storm R2 250-S Скачать руководство пользователя

Страница: 17 / 56

R
O
N

G
G

N
G

FRONT RIGGINGS

PROCEDURE 4

Hinge

Plate

Footrest Release Lever

Hinge

Pins

Removing

1. Push the footrest release lever inward and rotate

the footrest outward.

2. Lift up on the footrest and remove from the wheel-

chair.

3. Repeat STEPS 1-2 for the opposite side of the wheel-

chair.

ADJUSTING FOOTREST HEIGHT

All Footrests Except Model P93M Footrests
(FIGURE 2)

1. Remove any accessory from the footrest(s).

2. Remove the footrest from the wheelchair. Refer to

INSTALLING/REMOVING FOOTRESTS in this pro-
cedure of the manual.

NOTE: Lay the footrest on a flat surface to simplify this
procedure.

3. Remove the hex bolt, coved washers and locknut

that secure the lower footrest to the footrest support.

4. Reposition the lower footrest to the desired height.

5. Reinstall the hex bolt, coved washers and locknut

that secure the lower footrest to the footrest support
and tighten securely.

6. Repeat STEPS 1-5 for the opposite side of the wheel-

chair footrest, if necessary.

7. Reinstall the footrest(s) onto the wheelchair. Refer

to INSTALLING/REMOVING FOOTRESTS in this
procedure of the manual.

8. Reinstall any accessory onto the footrest(s).

FIGURE 2 - ADJUSTING FOOTREST HEIGHT - ALL

FOOTRESTS EXCEPT MODEL P93M FOOTRESTS

NOTE: PW93ST style
footrest shown for clarity
only.

Footrest Support

Hex Bolt

Coved

Washer

Coved Washer

Locknut

Lower Footrest

FIGURE 1 - INSTALLING/REMOVING FOOTRESTS

This Procedure Includes the Following:

Installing/Removing Footrests

Adjusting Footrest Height

Replacing Heel Loops

Installing/Removing Elevating Legrests

Raising/Lowering Elevating Legrests and/or
Adjusting Calfpads

Adjusting/Replacing Telescoping Front
Rigging Support

INSTALLING/REMOVING
FOOTRESTS (FIGURE 1)

Installing

1. Turn the footrest to the side (open footplate is per-

pendicular to wheelchair) and position the mounting
holes in the footrest hinge plates with the hinge pins
on the wheelchair frame.

2. Install the footrest hinge plates onto the hinge pins

on the wheelchair frame.

3. Push the footrest towards the inside of the wheel-

chair until it locks into place.

NOTE: The footplate will be on the inside of the wheel-
chair when locked in place.

4. Repeat STEPS 1-3 for opposite side of wheelchair.

WARNING

After ANY adjustments, repair or service and BE-
FORE use, make sure all attaching hardware is
tightened securely - otherwise injury or damage
may result.

Содержание Ranger II Storm R2 250-S

























































Результаты поиска

Содержание Ranger II Storm R2 250-S

Отзывы:

Похожие инструкции для Ranger II Storm R2 250-S

Бренды по названию

Популярные бренды

Invacare Ranger II Storm R2 250-S, Руководство пользователя

Результаты поиска

Содержание Ranger II Storm R2 250-S

Отзывы:

Похожие инструкции для Ranger II Storm R2 250-S

Бренды по названию

Популярные бренды