Invacare A-4 Series Скачать руководство пользователя

Страница: 46 / 68

A-4

Part No. 1110545

WHEEL LOCK ADJUSTMENT/REPLACEMENT (FIGURE 7)

NOTE: INVACARE recommends UNDER mount wheels locks when engaging in any contact sport.
NOTE: Before adjusting or replacing the High/Under mount wheel locks, ensure that the tires are

inflated to the recommended psi on the sidewall of the tire.

1. Loosen the hex screw(s) that secure the High/Under mount wheel locks to the seat

frame.

2. Perform one (1) of the following:

REPLACING THE HIGH/UNDER MOUNT WHEEL LOCK:

1. Remove the hex screws and remove the existing wheel lock from the

wheelchair.

2. Install the NEW wheel lock.

ADJUSTING THE HIGH/UNDER MOUNT WHEEL LOCK:

1. Proceed to STEP 3.

3. Adjust position of wheel lock until the 3/16-inch engagement with the tire is obtained.

NOTE: Any wheel lock adjustment should embed the wheel lock shoe at least 3/16-inch into the

pneumatic tire when engaged.

4. Engage the wheel locks and push against the wheelchair and determine if wheel locks

engage the rear wheels enough to hold the wheelchair.

5. Repeat the STEPS 3-4 until the wheel locks hold the wheelchair.

Hex Screws

High Mount Wheel Lock

FIGURE 7 - WHEEL LOCK ADJUSTMENT/REPLACEMENT

3/16-inch

Tire

High Mount

Wheel Lock

Shoe

SECTION 5

WHEELS

REPLACING/ADJUSTING CASTERS (FIGURE 8)

NOTE: Both casters should be the same size.

1. REPLACING CASTERS ONLY - If replacing the EXISTING caster with the same size NEW

caster, note the mounting position of the EXISTING caster.

2. Remove the bolt and locknut that secure the caster and axle spacers to the fork.

Hideaway

Undermount

Wheel Lock

Hex Screws

Wheelchair

Frame

Wheel Lock Shoe

FRONT

REAR

3/16-inch

Under Mount

Wheel Lock

Shoe

Tire

Содержание A-4 Series





































































Результаты поиска

Содержание A-4 Series

Отзывы:

Похожие инструкции для A-4 Series

Бренды по названию

Популярные бренды

Invacare A-4 Series, Руководство владельца по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание A-4 Series

Отзывы:

Похожие инструкции для A-4 Series

Бренды по названию

Популярные бренды