background image

Invacare Corporation

www.invacare.com

USA

Canada

One Invacare Way

570 Matheson Blvd E Unit 8

Invacare is a registered trademark of

Elyria, Ohio  USA

Mississauga Ontario

Invacare Corporation.

44036-2125

L4Z 4G4 Canada

Yes, you can. and A-4 are trademarks of

800-333-6900

800-668-5324

Invacare Corporation.

3-in-1 and  WD-40 are registered

trademarks of the WD-40 Company.

Teflon is a registered trademark of E.I.

Du Pont De Nemours and Company.

© 2002 Invacare Corporation

Part No. 1110545

Rev A  09/02

LIMITED WARRANTY

PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH

FEDERAL LAW APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4, 1975.
This warranty is extended only to the original purchaser/user of our products.
This warranty gives you specific legal rights and you may also have other legal rights which

vary from state to state.
Invacare warrants the frame to be free from defects in materials and workmanship for a

lifetime from date of purchase; all remaining components for one (1) year from date of

purchase except upholstered materials, padded materials and tires/wheels. If within such

warranty period any such product shall be proven to be defective, such product shall be

repaired or replaced at Invacare's option. This warranty does not include any labor or

shipping charges incurred in replacement part installation or repair of any such product.

Invacare’s sole obligation and your exclusive remedy under this warranty shall be limited

to such repair and/or replacement.
For warranty service, please contact the dealer from whom you purchased your Invacare

product. In the event you do not receive satisfactory warranty service, please write directly

to Invacare at the address below, provide dealer’s name, address, and the date of purchase,

indicate nature of the defect and, if the product is serialized, indicate the serial number. Do

not return products to our factory without our prior consent.
LIMITATIONS AND EXCLUSIONS: THE FOREGOING WARRANTY SHALL NOT

APPLY TO SERIAL NUMBERED PRODUCTS IF THE SERIAL NUMBER HAS BEEN

REMOVED OR DEFACED, PRODUCTS SUBJECTED TO NEGLIGENCE, ACCIDENT,

IMPROPER OPERATION, MAINTENANCE OR STORAGE, PRODUCTS MODIFIED

WITHOUT INVACARE’S EXPRESS WRITTEN CONSENT INCLUDING, BUT NOT

LIMITED TO, MODIFICATION THROUGH THE USE OF UNAUTHORIZED PARTS OR

ATTACHMENTS; PRODUCTS DAMAGED BY REASON OF REPAIRS MADE TO ANY

COMPONENT WITHOUT THE SPECIFIC CONSENT OF INVACARE, OR TO A

PRODUCT DAMAGED BY CIRCUMSTANCES BEYOND INVACARE’S CONTROL,

AND SUCH EVALUATION WILL BE SOLELY DETERMINED BY INVACARE. THE

WARRANTY SHALL NOT APPLY TO PROBLEMS ARISING FROM NORMAL WEAR

OR FAILURE TO ADHERE TO THESE INSTRUCTIONS.
THE FOREGOING EXPRESS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY

OTHER WARRANTIES WHATSOEVER, WHETHER EXPRESS OR IMPLIED,

INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE, AND THE SOLE REMEDY FOR VIOLATIONS OF ANY

WARRANTY WHATSOEVER, SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF

THE DEFECTIVE PRODUCT PURSUANT TO THE TERMS CONTAINED HEREIN. THE

APPLICATION OF ANY IMPLIED WARRANTY WHATSOEVER SHALL NOT EXTEND

BEYOND THE DURATION OF THE EXPRESS WARRANTY PROVIDED HEREIN.

INVACARE SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL

DAMAGES WHATSOEVER.
THIS WARRANTY SHALL BE EXTENDED TO COMPLY WITH STATE/PROVINCIAL

LAWS AND REQUIREMENTS.

Содержание A-4 Series





































































Отзывы: