Invacare A-4 Series Скачать руководство пользователя

Страница: 39 / 68

Part No. 1110545

A-4

SECTION 4

FRAME

FIGURE 11 - ADJUSTING WHEELBASE WIDTH

ADJUSTING WHEELBASE WIDTH

(FIGURE 11)

NOTE: Perform this procedure on one (1) side of the wheelchair at a time for ease of adjustment.

1. Open the camber clamp. Refer to OPENING/CLOSING CAMBER CLAMPS in this

procedure of the manual.

WARNING

NEVER position the camber inserts in the axle tube with more than 3-inches

(12 indexing marks showing) of the camber insert outside of the axle tube.

Otherwise, the camber inserts will not be securely tightened in the axle tube

resulting in possible injury to the user or damage to the wheelchair.

2. Position the camber insert to the desired position. Make sure there are no more than

3-inches (12 indexing marks showing) of the camber inserts outside of the axle tube.

3. Slide the indexing ring on the camber insert until it is flush with the camber clamp.

NOTE: Before using the wheelchair, make sure both camber inserts are set at the same indexing

mark. This will make sure the distance between the rear wheel and the wheelchair is the same on

both sides.

WARNING

QUICK RELEASE LEVERS - Make sure the quick release levers are in the

CLOSED position BEFORE using the wheelchair, otherwise personal

injury or damage to the wheelchair may result.
STANDARD CAMBER CLAMPS - Make sure the socket screws are

securely tightened BEFORE using the wheelchair, otherwise personal

injury or damage to the wheelchair may result.

CAUTION

DO NOT close the quick-release levers or tighten the socket screws

without camber inserts in the axle tube. Damage to the axle tube will

occur.

4. Close the camber clamp. Refer to OPENING/CLOSING CAMBER CLAMPS in this

procedure of the manual.

5. Repeat STEPS 1-4 for the opposite side of the wheelchair.

Indexing Ring

Axle Tube

Camber

Clamp

Indexing Marks

Camber

Insert

Camber

Insert

Содержание A-4 Series





































































Результаты поиска

Содержание A-4 Series

Отзывы:

Похожие инструкции для A-4 Series

Бренды по названию

Популярные бренды

Invacare A-4 Series, Руководство владельца по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание A-4 Series

Отзывы:

Похожие инструкции для A-4 Series

Бренды по названию

Популярные бренды