Intimus 175 CC3, Руководство по эксплуатации

Страница: 4 / 20

175 SC2
175 CC3/CC4/CC5/CC6
Fig. 4
4
91239 4 01/14
CUTTER MAINTENANCE (cross-cut):
Cross cut cutters must be oiled after a
specific operating time. If the control
display (7) comes on proceed as
follows:
Spread some of the special oil provided on a
sheet of paper and then feed this into the cutter
via the feed slot.
The paper is drawn in and at the same time
the cutter is supplied with oil for the necessary
lubrication.
Note: This procedure is acknowledged
as follows to turn off the display after the
cutters have been oiled:
- Open the door until the control display (9)
lights up. The control displays (7) and (4)
flash.
- Press the reverse button (4) and keep it
held down until the control display (7) goes
out.
- Close the door again.
The cutters now start a cleaning cycle
automatically (forward and reverse run) and then
switch off. The machine is ready for use again.
Should you need to re-order the special oil see
“SPECIAL ACCESSORIES”.
AUTOMATIC ENERGY SAVING:
If the machine is not used for a while it
automatically switches off after about 5 minutes.
The function button (1) LED display for
“Ready” goes out. Press the function button
briefly to turn it on again.
USA
MAINTENANCE
MALFUNCTIONS
ACCESSORIES
TECHNICAL DATA
DISPOSING OF THE MACHINE:
Dispose of the machine in an
environmentally sound fashion at the end
of its useful service life. Do not dispose of
any of the parts included in the machine
or its packaging with household trash.
DISPOSING
Description Order-No.
Plastic bag, 23.62 x 19.68 x 39.37 x 0,002 in. 99952
Lubricant, 110 ml bottle (cross-cut) 88035
Note: For orders of special accessories and spare parts, please contact your dealer.
Cutting width:
175SC2: 0.15 in. (strips)
0.23 in. (strips)
175CC3: 0.16x1.81 in. (cross-cut)
175CC4: 0.07x0.59 in. (cross-cut)
175CC5: 0.03x0.47 in. (cross-cut)
175CC6: 0.03x0.18 in. (cross-cut)
Cutting speed:
175SC2: 4.72 in./sec.
175CC3/CC4: 5,12 in./sec.
175CC5: 5.90 in./sec.
175CC6: 9.05 in./sec.
Cutting capacity:
175SC2 0.15 in.: 40-45 sheets (70g/m
2
)
175SC2 0.23 in.: 65-70 sheets (70g/m
2
)
175CC3: 40-50 sheets (70g/m
2
)
175CC4: 25-30 sheets (70g/m
2
)
175CC5: 15-17 sheets (70g/m
2
)
175CC6: 8-10 sheets (70g/m
2
)
Supply voltage: 230V/50Hz
240V/50Hz
120V/60Hz
100V/50/60Hz
Pre-fusing:
230V/50Hz: 16 amps (slow-blow)
240V/50Hz: 13 amps (slow-blow)
120V/100V/50/60Hz: 20 amps (slow-blow)
Working width: 15.94 in.
Noise level: approx. 52 dB(A)
Power: 1.9 kW
Dimensions (WxDxH): 25.98x22.05x41.34 in.
Weight: approx. 198 lb.
MAINTENANCE
CLEANING THE PHOTOCELLS (Fig. 4):
If paper particles should come to rest in the
inlet guide (for example after a paper jam) it is
possible that the machine will not turn off, due to
the broken light barrier.
To remove these paper strips and also to clean
the photocell, pass another sheet of paper
through the feed slot, or switch the machine to
reverse and wipe both “eyes” of the photocell
with a brush.
4
MATERIAL JAM IN THE MACHINE:
(Auto reverse function)
If a jam is caused by too much material being fed
in the following happens:
- The cutters jam, then run in reverse for a short
time (material is released) and stop. The motor
switches off. The control display (6) comes
on.
Proceed as follows:
- Remove the paper that has been fed back.
- The cutters now run forwards automatically
and shred the remaining paper in the cutters.
During the forward run the forward button (2)
LED display comes on. The control display
(6) goes out.
- Continue shredding with less paper.
LIGHT BARRIER COVERED
WHEN DOOR OPENED:
Should there still be material in the feed slot
when the door is opened, the motor switches off
and the cutters stop. The control display (6)
comes on.
Close the door and acknowledge the status
by pressing the forward button (2) briefly.
The existing material is fed to the cutters and
shredded.
LIGHT BARRIER COVERED
WHEN MACHINE TURNED ON:
Should there still be material in the feed slot
when the machine is switched on the control
display (6) comes on.
Remove the material and acknowledge the
status by pressing the forward button (2) briefly.
MOTOR PROTECTION:
Should the motor be overloaded it switches off.
The control display (9) comes on.
The machine can be started again after a cooling
down period of about 15 – 20 minutes (depending
on the model and the room temperature).
ELECTRICAL FAULT:
If the control display (9) flashes together with
the function button (1) LED display or only
the control display (8)
flashes
there is an
electrical fault. The machine cannot be started.
In this case please contact your dealer.
FAULT CHECK LIST:
Should the machine not work, check the
following points:
- is the plug connected to the power supply?
- is the door closed?
- is the receptacle full?
Follow the instructions under „EMPTYING THE
RECEPTACLE“.
- is there a material jam in the machine?
Follow the instructions in “MATERIAL JAM IN
THE MACHINE”.
- is the
motor
overloaded?
See “MOTOR PROTECTION”.
If none of these test points apply, please
contact your dealer.