Intimus 175 CC3, Руководство по эксплуатации

Страница: 2 / 20

175 SC2
175 CC3/CC4/CC5/CC6
<< The machine may not be operated by more
than one person at any given time!
The machine was designed for safe operation
by “one person only”.
<< During the shredding process no other
work may be performed on the machine
(for example cleaning, etc.)!
<< The machine is not a toy, and is not suitable
for use by children!
The overall technical safety concept of
this machine (dimensions, feed openings,
emergency shutdown devices etc.) does not
provide for any guarantee regarding hazard-
free operation by children.
<< Danger of injury! Keep all loose
articles of clothing, ties, jewe-
lery, long hair or other loose
objects away from opening!
<< Danger of injury! Never insert fingers into
opening!
<< In case of danger switch the machine off
with the mains switch, or with the emer-
gency switch, or unplug the machine!
<< Always unplug the machine from the
mains power supply before opening the
machine!
Repairs may only be performed by trained
personnel!
IMPORTANT SAFETY NOTES
SCOPE OF APPLICATION:
The document shredder intimus 175SC2/CC3/
CC4/CC5/CC6
is a machine for the destruction
of common written material.
The machine may only be used to
shred paper!
Shredding of other types of data carriers
and also of staples and paper clips with
the models with cutting width 0.03x0.47
in. (CC5) or 0.03x0.18 in. (CC6) may
lead to injuries (for example due to
splintering of hard materials etc.) and
damage to the machine (for example
destruction of the cutter etc.).
Exception: Single CD’s or 3.5” computer dis-
kettes can also be shredded with 0.15 in., 0.23
in., 0.16x1.81 in., 0.07x0.59 in. models.
INSTALLATION:
- Unpack and set machine upright.
- Place plastic sack into the receptacle.
- Plug in the machine (for instructions for the
necessary precautions see „TECHNICAL
DATA“.
The air vents in the housing are ne-
cessary for cooling and may not be
covered or closed!
The mains connection at the machine
must be freely accessible!
Only operate the machine in enclosed
rooms at temperatures between 10°C
and 25°C!
Fig. 2
4
Fig. 1
2
9
1
10
3
6
7
8
5
91239 4 01/14
USA
INITIATION
OPERATION
OPERATION
5 = Control display (Fig. 1)
“Load level of the motor”
Displays the current load level of the motor
during the shredding process via different
colour lights (see description under “DY-
NAMIC LOAD DISPLAY”).
6 = Control display (fig. 1)
“Material jam in machine”/ “Light barrier
covered when door opens or when
machine turned on”
For the procedures see the relevant
description under the “MALFUNCTION”
section.
a) “Material jam in machine”
Comes on when too much material has
been fed into the cutters.
The cutters jam, then run in reverse for a
short time and stop. The motor switches
off.
b) “Light barrier covered
when door open”
Comes on when there is still material in
the feed slot when the door is opened.
The cutters stop. The motor switches
off.
c) “Light barrier covered
when machine turned on”
Comes on when there is still material
in the feed slot when the machine is
switched on.
BEDIENUNGSELEMENTE:
1 = Function button (fig. 1)
“Ready”/ “Off” / “Stop“
This button has three functions:
a) “Ready”
The machine changes to “Ready” if you
press this button briefly.
At the same time the integral LED
display comes on.
b) “Off”
The machine switches off if it is in the
“Ready” mode and the button is held
down for about 3 seconds.
Note: The machine switches off
automatically if it is not used for about 5
minutes.
c) “Stop”
If you press this button briefly when the
cutters are running they switch off and
stop.
2 = Forwards button (fig. 1)
This button has two functions:
a) If this button is pressed briefly, the
cutting mechanism runs forwards for a
few seconds, e.g. to remove remaining
material from the cutting mechanism.
At the same time the integrated LED
display lights up.
b) If this button is pressed and held
for approx. two secs., the cutting
mechanism runs forwards continually
and materials to be shredded can be fed
into the machine. At the same time the
integrated LED display lights up.
3 = Reverse button (fig. 1)
If you press this button the cutters run
backwards. At the same time the integral
LED display comes on.
4 = Light barrier (Forward motion) (fig. 3)
The shredding procedure starts as soon as
material is fed into the feed slot.
At the same time the integral forward button
LED display comes on.
2