Interroll SH 1100 Скачать руководство пользователя страница 44

Страница: 44 / 88

Interroll Module belt conveyor SH 1100

Initial startup and operation

Version 1.0 (06/2022) en

Translation of original operating instructions

Operation

Before every operation

start

Check the module for visible damage.

Ensure that all safety devices operate flawlessly.

Ensure that only authorized persons are in the operating area of the module.

Ensure that the module is running freely and that no parts are jammed.

Remove equipment or material that is not required from the operating area.

Specify and monitor correct placement of the conveying good.

During operation

WARNING

Danger from rotating parts

Crushing and serious injuries due to parts of the body and clothing being pulled into the
module!

Do not remove the protective covers.

Wear personal protective equipment.

Avoid jewelry and bracelets.

CAUTION

Danger from shearing between product and universal support of side guide

Do not reach in from the side.

Take additional protective measures.

If material is jammed between side guides, switch off the module and ensure that it cannot be
started accidentally, then remove the fault.

Procedure in case of

accident or fault

Press the Emergency Stop pushbutton, power it down and ensure that it cannot be switched
on accidentally.

In case of an accident: Provide first aid and make an emergency call, if necessary.

Inform qualified personnel.

Have the fault corrected by qualified personnel.

Restart the module only after this has been approved by qualified personnel.

Содержание SH 1100

























































































Результаты поиска

Содержание SH 1100

Отзывы:

Похожие инструкции для SH 1100

Бренды по названию

Популярные бренды

Interroll SH 1100, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SH 1100

Отзывы:

Похожие инструкции для SH 1100

Бренды по названию

Популярные бренды