background image

Interroll Module belt conveyor SH 1100

Installation

Version 1.0 (06/2022) en
Translation of original operating instructions

35

Straight module belt

conveyor (80) - straight

module belt conveyor (50)

The modules can be connected with each other in different ways:

• Horizontal
• Up to max. 4° ascending
• Up to max. 4° descending

The conveying direction is only allowed from left to right (HD pulling).

1

2

7

1

5

4

6

1

3

8

1

Torx screw

5

Module belt conveyor HD contact guard
(top)

2

Module belt conveyor

6

Module belt conveyor

3

Module belt conveyor contact guard

7

Module connector

4

Module belt conveyor HD contact guard
(bottom)

8

Washer

4

Position the modules to be connected (2, 6) in such a way that the side profiles are aligned.

4

Align the top edges of the modules by using the height-adjustable feet of the supports.

4

Check horizontal alignment with a spirit level or rotation laser.

4

Secure the adjusted height.

4

Attach contact guard (3) at side profile of module belt conveyor (2) at idler axle and fasten it
with screws (1).

4

Attach contact guard (4) at the bottom at side profile of module belt conveyor (6) for the
drum motor (HD) and fasten it with screws (1).

4

Attach contact guard (5) at the top at side profile of module belt conveyor (6) for the drum
motor (HD) and fasten it with screws (1).

4

Connect the contact guards (3, 4) form-fit with the module connectors (7) with each other
and fasten with screws (1) and washers (8).

4

Fasten the module torsion-free, e.g., by anchoring it to the floor or to adjacent components.

Содержание SH 1100

























































































Отзывы: