Interroll SH 1100 Скачать руководство пользователя страница 28

Страница: 28 / 88

Interroll Module belt conveyor SH 1100

Installation

Version 1.0 (06/2022) en

Translation of original operating instructions

Installing the reflector

Installing the reflector

Mounting bracket (U-bracket)

Clamping plate

Sensor holder

Torx screw

Reflector

Universal support

Side frame

Install the reflector (3) opposite the photo cell.

Loosen screw (6) in the universal support (7), but do not remove it.

Bring clamping plate (5) with universal support (7) from below into position at the profile of
the side frame (4).
The profile of the side frame is located between clamping plate and universal support.

Tighten the screw (6) at the desired location.

After installing the photo cell and reflector: Connect the photo cell to the control of the
module with a cable.

Check whether both LEDs are lit.

If the yellow LED flashes, position reflector and photo cell relative to each other.

LED green

LED yellow

Meaning

Off

Photo cell is operational.
No signal from reflector.

Photo cell is correctly adjusted.
Light beam is well reflected.

Flashing

Photo cell is operational.
Weak signal.
Reflector is dirty, damaged or not correctly adjusted.

Содержание SH 1100

























































































Результаты поиска

Содержание SH 1100

Отзывы:

Похожие инструкции для SH 1100

Бренды по названию

Популярные бренды

Interroll SH 1100, Инструкция по установке и эксплуатации

Результаты поиска

Содержание SH 1100

Отзывы:

Похожие инструкции для SH 1100

Бренды по названию

Популярные бренды