Interphase iScan V90 Скачать руководство пользователя

Страница: 2 / 40

To Our Customer:

Thank you for choosing the

Interphase iScan V90 Forward Scanning Sonar. Throughout

the development of this product, we have tried to make sure that we included all of the

suggestions made by owners of our earlier sonar models. Selection of features, ease of use,

superior performance and outstanding reliability were the benchmarks upon which all

important design decisions were made. We feel proud of the

iScan V90 and your satisfaction

is very important to us. To this end, we welcome any comments or suggestions that you might

have in regard to this equipment.

It is very important that you complete and return the

WARRANTY REGISTRATION

CARD within 15 days of purchase so that we have a record of your purchase, both to protect

your warranty and to allow us a method to contact you about future enhancements, etc.

Sincerely,

INTERPHASE TECHNOLOGIES, INC.

2880 Research Park Drive, #140

Soquel, CA 95073

Phone: (831) 477-4944

Fax: (831) 462-7444

Email: [email protected]

Website: www.interphase-tech.com

Interphase iScan V90™ is a trademark of Interphase Technologies, Inc.

Publication # = V90 1.2

Содержание iScan V90









































Результаты поиска

Содержание iScan V90

Отзывы:

Похожие инструкции для iScan V90

Бренды по названию

Популярные бренды

Interphase iScan V90, Руководство по эксплуатации

Результаты поиска

Содержание iScan V90

Отзывы:

Похожие инструкции для iScan V90

Бренды по названию

Популярные бренды