2. Using provided twist on or other approved connectors, connect the fixture wires to the supply wires as follows:
(See Figure 3)
a. Connect the black fixture wire marked 120V to the black (hot) supply wire.
b. Connect the white fixture wire marked COM to the white (neutral) supply wire.
c. Connect the bare copper (fixture ground) wire to the supply grounding wire.
3. Make sure that all wires and connections are inside the mounting wiring compartment and that the cover is
properly sealed to keep moisture out. To weatherproof fixture, seal all holes in housing (mounting conduit, plugs,
photocontrols, etc.) with silicone sealant.
4. Release clip and swing hinged fixture lens door open. Screw lamp into socket in lampholder until finger-tight.
5. Close lens door and secure clip, making sure that gasket is in place and compressed to seal out moisture.
6. To operate, restore power to the circuit and switch light on.
AIMING FIXTURE
WARNING: Electric shock hazard.
Do not turn mounting arm more than 360˚ after wires are connected. Excessive twisting of wires
may loosen connections.
1. Turn off power at circuit breaker or fuse box. Rotate mounting arm until light is pointing in the desired direction.
Tighten locknut to secure.
2. Loosen mounting arm bolt (do not remove) and tip fixture to desired angle. Retighten bolt to secure.
3. Turn power on and check aim. If adjustment is needed, turn power OFF at circuit breaker or fuse box and allow
fixture to cool before adjusting.
LAMP REPLACEMENT
CAUTION: Use lamp of correct type and wattage as specified on fixture.
1. Turn off power at circuit breaker or fuse box. Allow fixture and lamp to cool.
2. Release retaining clip and swing hinged fixture lens door open. Remove old lamp and replace with new lamp of
correct type and wattage. Screw lamp into socket in lampholder until finger-tight.
3. Close lens door and secure clip, making sure that gasket is properly seated, free of debris, and compressed to seal
out moisture.
4. Turn power back on.
5. Properly dispose of lamp per manufacturer’s recommendations.
LIMITED 1 YEAR WARRANTY
If within one (1) year from the date of purchase, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace it, at its sole option, free of
charge. This warranty is extended to the original purchaser only and is not transferable. This warranty does not apply to: (a) damage to units caused by accident, dropping or abuse in
handling, acts of God or any negligent use; (b) units which have been subject to unauthorized repair, opened, taken apart or otherwise modified; (c) units not used in accordance with
instructions; (d) damages exceeding the cost of the product; (e) sealed lamps and/or lamp bulbs; (f) the finish on any portion of the product, such as surface and/or weathering, as this is
considered normal wear and tear; (g) transit damage, initial installation costs, removal costs, or reinstallation costs.
INTERMATIC INCORPORATED WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS
OR IMPLIED WARRANTIES. ALL IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR
PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS LIMITED WARRANTY, AND SHALL BE OF THE SAME DURATION AS THE WARRANTY PERIOD
STATED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED WARRANTY, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased, or (b) mailing the product, along with proof of purchase, postage
prepaid to the authorized service center listed below. This warranty is made by: Intermatic Incorporated/After Sales Service/7777 Winn Rd., Spring Grove, Illinois 60081-9698/815-675-
7000 http://www.intermatic.com Please be sure to wrap the product securely to avoid shipping damage.
THESE INSTRUCTIONS DO NOT COVER ALL VARIATIONS IN EQUIPMENT, NOR DO THEY PROVIDE FOR ALL SITUATIONS RELATED
TO FIXTURE INSTALLATION, OPERATION OR MAINTENANCE. FOR FURTHER INFORMATION CONTACT YOUR DISTRIBUTOR OR
INTERMATIC INCORPORATED - SPRING GROVE, ILLINOIS 60081 (815) 675-7000 www.intermatic.com
158HL12119
Figure 3
120 V
COM
COM
IGN-01
LAMP
X3
X1
X2
