Interlogix ATS1500A-IP-LP Скачать руководство пользователя страница 280

Страница: 280 / 376

Chapter 5: Menu reference

274

Advisor Advanced ATSx500A(-IP) Installation and Programming Manual

9.3.n.5 GSM Setup

1>SIM card PIN
0000

The GSM Setup menu lets you set up GSM reporting and control.

Notes

• Before using the SIM card in the system, insert it into a mobile phone and

verify its validity, checking the credit and sending a test SMS message.

• Before changing SIM card, delete the SMS center number. Otherwise, the

system will overwrite the default SMS center number on the new SIM card

with this number. See “9.3.n.6.1 SMS Center num” on page 278 for more

details.

9.3.n.5.1 SIM card PIN

1 SIM card PIN
>0000<

The SIM card PIN menu lets you configure the PIN of the SIM card.
This menu can also show the following messages:
• PUK required

• One trial left
See “1.2.8.1 PIN status” on page 133 for more detailed explanation for these

messages.
This menu does not have any functionality if the PIN is not required for this SIM

card.

9.3.n.5.2 Networks

1>Net.selection
Automatic

The Networks menu lets you configure the GSM network settings.

9.3.n.5.2.1 Net.selection

1 Net.selection
>Automatic<

The Network selection menu lets you define the preferred GSM network. Enter

the GSM network numerical code. If the code is not entered, the network is

chosen automatically.

9.3.n.5.2.2 Sel.net.only

2 Sel.net.only
>No<

If the Selected network only option is set to Yes, only the network selected in the

“9.3.n.5.2.1 Net.selection” above is allowed for the communication. Otherwise,

Содержание ATS1500A-IP-LP

























































































































































































































































































































































































Результаты поиска

Содержание ATS1500A-IP-LP

Отзывы:

Похожие инструкции для ATS1500A-IP-LP

Бренды по названию

Популярные бренды

Interlogix ATS1500A-IP-LP, Инструкция по установке и программированию

Результаты поиска

Содержание ATS1500A-IP-LP

Отзывы:

Похожие инструкции для ATS1500A-IP-LP

Бренды по названию

Популярные бренды