background image

Copyright

1997, Intergraph Corporation including this documentation, and any software and its file formats and audio-visual

displays described herein; all rights reserved; may only be used pursuant to the applicable software license
agreement; contains confidential and proprietary information of Intergraph and/or other third parties which is
protected by copyright, trade secret and trademark law and may not be provided or otherwise made available without
prior written authorization.

Product ID Information

The product ID information is located on the back of the base unit.

Power Input Rating

The unit’s power input rating and other power information for the system is stated in Chapter 2 under “Fixed Power
Supply (MPWS131)” or “Redundant Power Supplies (MPWS138).”

FCC Statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15
of the FCC Rules.  These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment.  This equipment generates, uses, and can radiate radio
frequency energy.  If the equipment is not installed and used in accordance with the instruction manual, it may cause
harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.

CDC Statement

This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in
the Radio Interference Regulations of the Canadian Department of Communications.

Содержание InterServe 600 Series









































































































Отзывы: