background image

7.4 Control and protection function of unit

7.4.1 The unit has the following protection functions 

1) Current cut-off protection

2) Power supply phase sequence protection

3) Protection for over-low suction pressure 

4) Protection for compressor overcurrent

5) Protection for compressor overload

6) Anti-freezing protection

7) Protection for over-high discharge pressure

8) Protection for outlet and inlet water temperature 

difference 

7.4.2 The unit also has other control functions: 

1) Manual test function

2) Plug and play system

3) RS-485/RS232 Standard serial communication port.

7.5 Troubleshooting

Table 7-1

Error

Possible reason

Air or other non-condensing gas still 

in the system

Detect and settle measure

Discharge gas from fluorin charging inlet. Re-vacuum the system if 

necessary.

Air or other non-condensing gas still 

in the system

Discharge gas from fluorin charging inlet. Re-vacuum the system if 

necessary.

Fins in the condenser are dirty or 

foreign substance blocking fins.  
Insufficient chilling air volume or 

condenser fan error 
Excessive high air suction pressure 
Excessive refrigerant charging volume 
Over high ambient temperature

See “Excessive high air suction pressure” 
Discharge the excessive refrigerant

Excessive refrigerant charging volume 
Over high temperature in chilling water inlet

Insufficient water flow volume

Incrustant in evaporator 

Insufficient water flow

Incrustant in water side of heat exchanger
Over high temperature in chilling water inlet
Excessive high air suction pressure 
Over low temperature of chilling water

Excessive low air suction pressure 

Excessive refrigerant charging volume 
Insufficient refrigerant charging volume 
Insufficient air flow volume
Air loop short-circuit

Over heat air in the side of air heat exchanger

Refrigerant leakage or insufficient 

refrigerant volume

Over low temperature in chilling water 

inlet and outlet

Discharge the excessive refrigerant

Check and installation state

Test leakage or charge sufficient refrigerant to the system 

Eliminate incrustant 

Eliminate incrustant 
Check water temperature
See “Excessive high air suction pressure” 
Check chilling water temperature

Refrigerant leakage or insufficient 

refrigerant volume

Test leakage or charge sufficient refrigerant to the system 

See “Excessive low air suction pressure”  
Check ambient temperature around it
Discharge the excessive refrigerant
Charge sufficient refrigerant to the system
Check fan rotating direction
Reason about remove air short-circuit

Insufficient frost-removal operation

Error comes out from 4-way valve or thermal resistor. Replace a new one if necessary.

Check temperature difference at water inlet and outlet, and adjust the 

water flow volume 

Check temperature difference at water inlet and outlet, and adjust the

water flow volume 

Check thermal insulation layer of water pipe and the specification of this layer

Check ambient temperature

Over cool air in the side of air heat 

exchanger
Refrigerant leakage or insufficient r

efrigerant volume
Excessive low air suction pressure 

Check ambient temperature

Test leakage or charge sufficient refrigerant to the system 

See “Excessive low air suction pressure” 

Check and repair the condenser fan, recover the normal operation

Clean condenser fins.

Insufficient chilling water flow volume

Gas still in water loop

Error comes from pump or flow-type water volume control. Check and 

repair or replace a new one.  
Discharge air

Thermal resistor error
Over high air expelling pressure

Upon error have been confirmed, please replace a new one.
See “Over high air expelling pressure”

Hi-pressure switch error

Upon error have been confirmed, please replace a new one.

    Over high air 

discharge pressure

(Cooling operation)

    Over low air 

discharge pressure

(Cooling operation)

    Over low air 

suction pressure 

(Cooling operation)

    Over high air 

discharge pressure 

(Heating operation)

    Over low air 

discharge pressure 

(Heating operation)

  Over low air 

 suction pressure 

(Heating operation)

  Compressor stops 

because of freeze-proof

protection (Cooling 

operation)

Compressor stops because 

of Hi-pressure protection

    Over high air 

suction pressure 

(Heating operation)

Over high air 

suction pressure

(Cooling operation)

Network ON

ć

 

A

#

 

 

 

 

 

 

 

 

O&I manual

20

Содержание ICHS-420KC-5


































Отзывы: