background image

 

 

 

TTERY DISCOECT 

THE SYSTEM 

A typical motor home may use one or two relays to disconnect the batteries. These relays are 
usually independent and operate from a switch panel located inside the coach. A harness is 
used to connect from the panel to the relays. The Intellitec panels are offered in four models. 
They are: 

BD0 - Single battery system, with a cable and monitor panel with an on/off indicator 

BD1 - Single battery system, with a cable and monitor panel with an on/off indicator and digital 
voltmeter 

BD2 - Dual battery system, with cable and monitor panel with two on/off indicators and ignition 
interlock relay. 

BD3 - Dual battery system, with cable and monitor panel with two on/off indicators, digital 
voltmeter, and ignition interlock relay. 

Note: BD0 panel can be interchanged with BD, and BD2 can be interchanged with BD3 

The dual relay panels include an ignition interlock relay that opens the power circuit to the 
chassis battery relay when the ignition is turned on, to prevent the battery from being acci-
dently opened when the engine is running. 

A typical circuit is shown in FIGURE 5 and FIGURE 6. The switches are each double pole, 
double throw, momentary, center off. Operating the switch in either direction will cause the 
relays to open or close, depending on the polarity of the voltage applied. 

FUSES 

There are two 5 Amp fuses for the system, mounted on each relay. Looking at the relay with 
cap at the top, the fuse on the right feeds the LED indicator and, if so equipped, the digital 
voltmeter. The fuse on the left feeds the power to the switch that operates the solenoid. 

INTELLITEC 

PDX RV LLC 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
                         BD0 (BLACK/SILVER) 01-00066-004 

http://www.pdxrv.com/catalog/i2755.html

 

                         BD0 (BROWN/GOLD) 01-00066-000 

http://www.pdxrv.com/catalog/i1399.html

 

 
 
 
                         BD1 (BLACK/SILVER) 01-00066-005 

http://www.pdxrv.com/catalog/i2757.html

 

                         BD1 (BROWN/GOLD) 01-00066-001 

http://www.pdxrv.com/catalog/i1364.html

 

 
 
 
                         BD2 (BLACK/SILVER) 01-00066-006 

http://www.pdxrv.com/catalog/i2758.html

 

                         BD2 (BROWN/GOLD) 01-00066-002 

http://www.pdxrv.com/catalog/i1363.html

 

 
 
 
                         BD3 (BLACK/SILVER) 01-00066-007 

http://www.pdxrv.com/catalog/i2759.html

 

                         BD3 (BROWN/GOLD) 01-00066-003 

http://www.pdxrv.com/catalog/i1400.html

     

Содержание Battery Disconnect BD0
























Отзывы: