Intellinet 523967 Скачать руководство пользователя | Manualshive

Страница: 126 / 128

background image

Application Protocol

Port

Number

Telnet TCP

23

FTP TCP

21

SMTP TCP

25

POP3 TCP

110

H.323 TCP

1720

SNMP UCP

161

SNMP Trap UDP

162

HTTP TCP

80

PPTP TCP

1723

PC Anywhere TCP

5631

PC Anywhere UDP

5632

PPPoE:

Point-to-Point Protocol over Ethernet. Point-to-Point Protocol is a secure

data transmission method originally created for dial-up connections; PPPoE is for
Ethernet connections.

PPPoE

relies on two widely accepted standards, Ethernet and

the Point-to-Point Protocol. It is a communications protocol for transmitting
information over Ethernet between different manufacturers.

Protocol:

A protocol is a set of rules for interaction agreed upon between multiple

parties so that when they interface with each other based on such a protocol, the
interpretation of their behavior is well-defined and can be made objectively, without
confusion or misunderstanding.

Router:

A router is an intelligent network device that forwards packets between

different networks based on network layer address information such as IP addresses.

Subnet Mask:

A subnet mask, which may be a part of the TCP/IP information

provided by your ISP, is a set of four numbers (e.g., 255.255.255.0) configured like
an IP address. It is used to create IP address numbers used only within a particular
network (as opposed to valid IP address numbers recognized by the Internet, which
must be assigned by InterNIC).

TCP/IP, UDP:

Transmission Control Protocol/Internet Protocol (TCP/IP) and

Unreliable Datagram Protocol (UDP). TCP/IP is the standard protocol for data

«
...
124
125
126
127
128
»

Содержание 523967

































































































































Отзывы:

Нет отзывов

Похожие инструкции для 523967

Бренд: Mobility Sound Страницы: 2

Бренд: US Robotics Страницы: 108

HT-TM01 TripMate

Бренд: Hootoo Страницы: 47

Pepwave Surf SOHO

Бренд: peplink Страницы: 151

Бренд: H3C Страницы: 18

Бренд: H3C Страницы: 69

Бренд: SUNDRAY Страницы: 20

Бренд: Air Live Страницы: 2

Бренд: Air Live Страницы: 103

Air Live WL-5470AP

Бренд: Air Live Страницы: 135

Бренд: Comcast Страницы: 16

Бренд: Comcast Страницы: 57

AIRLIVE WL-5430AP

Бренд: AirLive Страницы: 36

Бренд: Air Live Страницы: 2

Бренд: Air Live Страницы: 44

Бренд: Tornado Страницы: 7

Бренд: EnGenius Страницы: 4

Бренд: HomeMatic Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды