Intelligent Motion Systems MDrive34AC & 42AC Plus MDrive34AC Скачать руководство пользователя

Страница: 3 / 81

Important information

The drive systems described here are products for general use that conform to the

state of the art in technology and are designed to prevent any dangers. However,

drives and drive controllers that are not specifically designed for safety functions

are not approved for applications where the functioning of the drive could endan-

ger persons. The possibility of unexpected or un-braked movements can never be

totally excluded without additional safety equipment. For this reason personnel must

never be in the danger zone of the drives unless additional suitable safety equip-

ment prevents any personal danger. This applies to operation of the machine during

production and also to all service and maintenance work on drives and the machine.

The machine design must ensure personal safety. Suitable measures for prevention
of property damage are also required.

Qualification of personnel

Only technicians who are familiar with and understand the contents of this manual

and the other relevant documentation are authorized to work on and with this drive

system. The technicians must be able to detect potential dangers that may be

caused by setting parameters, changing parameter values and generally by the

operation of mechanical, electrical and electronic equipment.

The technicians must have sufficient technical training, knowledge and experience

to recognise and avoid dangers.

The technicians must be familiar with the relevant standards, regulations and safety

regulations that must be observed when working on the drive system.

Intended Use

The drive systems described here are products for general use that conform to the

state of the art in technology and are designed to prevent any dangers. However,

drives and drive controllers that are not specifically designed for safety functions

are not approved for applications where the functioning of the drive could endanger

persons. The possibility of unexpected or unbraked movements can never be totally

excluded without additional safety equipment.

For this reason personnel must never be in the danger zone of the drives unless

additional suitable safety equipment prevents any personal danger. This applies to

operation of the machine during production and also to all service and maintenance

work on drives and the machine. The machine design must ensure personal safety.

Suitable measures for prevention of property damage are also required.

In all cases the applicable safety regulations and the specified operating conditions,

such as environmental conditions and specified technical data, must be observed.

The drive system must not be commissioned and operated until completion of instal-

lation in accordance with the EMC regulations and the specifications in this manual.

To prevent personal injury and damage to property damaged drive systems must

not be installed or operated.

Changes and modifications of the drive systems are not permitted and if made all no

warranty and liability will be accepted.

The drive system must be operated only with the specified wiring and approved

accessories. In general, use only original accessories and spare parts.

The drive systems must not be operated in an environment subject to explosion
hazard (ex area).

Содержание MDrive34AC & 42AC Plus MDrive34AC


















































































Результаты поиска

Содержание MDrive34AC & 42AC Plus MDrive34AC

Отзывы:

Похожие инструкции для MDrive34AC & 42AC Plus MDrive34AC

Бренды по названию

Популярные бренды

Intelligent Motion Systems MDrive34AC & 42AC Plus MDrive34AC, Руководство по эксплуатации

Результаты поиска

Содержание MDrive34AC & 42AC Plus MDrive34AC

Отзывы:

Похожие инструкции для MDrive34AC & 42AC Plus MDrive34AC

Бренды по названию

Популярные бренды