manualshive.com logo in svg

Intelligent Motion Systems MDrive34AC & 42AC Plus MDrive34AC, Руководство по эксплуатации

Описание: Умные двигатели MDrive34AC & 42AC Plus MDrive34AC обеспечивают точное и эффективное движение для вашего оборудования. Для получения подробной информации о настройке и использовании, загрузите бесплатное Руководство по эксплуатации с manualshive.com. Максимизируйте возможности продукта с нашим подробным руководством.

Поделиться
Скачать
background image

The information in this book has been carefully checked and is believed to be accurate; however, no responsibility is assumed for 

inaccuracies.

Intelligent Motion Systems, Inc., reserves the right to make changes without further notice to any products herein to improve reliability, 

function or design.  Intelligent Motion Systems, Inc., does not assume any liability arising out of the application or use of any product or 

circuit described herein; neither does it convey any license under its patent rights of others. Intelligent Motion Systems and              

are 

trademarks of Intelligent Motion Systems, Inc.

Intelligent Motion Systems, Inc.’s general policy does not recommend the use of its products in life support or aircraft applications 

wherein a failure or malfunction of the product may directly threaten life or injury.  Per Intelligent Motion Systems, Inc.’s terms and 

conditions of sales, the user of Intelligent Motion Systems, Inc., products in life support or aircraft applications assumes all risks of such 

use and indemnifies Intelligent Motion Systems, Inc., against all damages.

TM

MDriveAC Plus Microstepping

Revision R031808

Copyright © Intelligent Motion Systems, Inc.

All Rights Reserved

MDriveAC Plus Motion Control Hardware Reference Change Log

Date

Revision

Changes

03/07/2006

R030706

Initial Release

04/13/2006

R041306

Corrected Motor+Driver weight specification for MDM34AC Plus, added notes on recommended mating connector for 
the M23 19-pin connector P1. Added MD-CS10x-000 and MD-CS-20x-000 To Appendix C.

05/04/2006

R050406

Removed Ambient Temperature Specification

05/25/2006

R052506

Replaced USB to SPI Cable Driver Installation with instructions relavent to Windows XP Service Pack 2. 

03/02/2007

R030207

Reworked IMS SPI Motor Interface Section, added information relevant to UL recognition. Added Enable Active High/
Low parameter for SPI, changed temperature specification to: -40°C to +75°C (non-condensing humidity), measured at 
the heat sink, and -40°C to +90°C (non-condensing humidity), measured on the motor.

12/17/2007

R121707

Minor updates and corrections. Made relevant to Firmware Version 3.0.02. Added Appendix for size 34 Linear slide.

03/18/2008

R031808

Added CW/CCW to the list of clock option labels for the differential input version. Functionality is the same as the 
up/down clock type. Added qualification os personnel and intended use statements to inside front.

Low Voltage Installation Information

Certain practices must be followed when installing the AC motor drives in order to meet the requirements of the Low Voltage Directive 73/23/EEC 
and as amended by Directive 93/68/EEC. The AC motor drives are components intended for installation within other electrical systems or ma-
chines. The system or machine builder must ensure their product complies with the applicable standards required for that equipment. The following 
information applies to the AC motor drives as far as the Low Voltage Directive is concerned.

1)   The AC motor drives are designed to be installed in a pollution degree level 2 environment.

2)   All control inputs and outputs are isolated from AC power with a basic insulation rating. The minimum clearance and creepage distance 

on the printed wiring board from the AC input to the control inputs and outputs is 3 millimeters. This is representative of an impulse 
rating of 4 KV (1.2/50 us) as referenced in standard EN50178.

3)  The control inputs and outputs may require an additional level of protection against direct contact if such protection is required by the 

standards governing the overall system or machine and its intended environment. It is the machine builder’s responsibility to provide 
this protection if needed.

4)   Be sure to wire the AC power and earth ground connection as shown in the operator’s manual.

5)   All cautions and warnings listed throughout the operator’s manual must be followed to insure safe system operation.

UL Application Details and Conditions of Acceptance

The UL Application Details and Conditions of Acceptance are located on the wed at http://www.imshome.com/CE_conformity.html.

Содержание MDrive34AC & 42AC Plus MDrive34AC


















































































Отзывы:

Нет отзывов

Похожие инструкции для MDrive34AC & 42AC Plus MDrive34AC

D-Link PCMCIA WIRELESS ASAPTER DWL-650 Quick Install Manual preview
PCMCIA WIRELESS ASAPTER DWL-650
Бренд: D-Link Страницы: 5
D-Link PowerLine DHP-W611AV User Manual preview
PowerLine DHP-W611AV
Бренд: D-Link Страницы: 78
Q-See QC814 Specifications preview
QC814
Бренд: Q-See Страницы: 2
Dentsply Sirona inLab Speedcure 9494800 Instruction Manual preview
inLab Speedcure 9494800
Бренд: Dentsply Sirona Страницы: 91
ICP DAS USA PISO-725 Series Quick Start Manual preview
PISO-725 Series
Бренд: ICP DAS USA Страницы: 8
ZALMAN ZM-MFC1 Combo User Manual preview
ZM-MFC1 Combo
Бренд: ZALMAN Страницы: 7
Comtrend Corporation WAP-5922MP Quick Install Manual preview
WAP-5922MP
Бренд: Comtrend Corporation Страницы: 4
Meinberg CPU-C15G2 Setup Manual preview
CPU-C15G2
Бренд: Meinberg Страницы: 14
IceTech POD-51EH-C541U-12 Operating Instructions Manual preview
POD-51EH-C541U-12
Бренд: IceTech Страницы: 8
Intel IXP28 Series Manual preview
IXP28 Series
Бренд: Intel Страницы: 154
Altera Cyclone IV GX Reference Manual preview
Cyclone IV GX
Бренд: Altera Страницы: 40
Milesight Pro UR32 Quick Start Manual preview
Pro UR32
Бренд: Milesight Страницы: 15
Kontron MSP8040 Series User Manual preview
MSP8040 Series
Бренд: Kontron Страницы: 32
WTI NPS-16HD20-1 User Manual preview
NPS-16HD20-1
Бренд: WTI Страницы: 178
S&T Kontron CP3005 Series User Manual preview
Kontron CP3005 Series
Бренд: S&T Страницы: 115
Intel Braswell Series Technical Manual preview
Braswell Series
Бренд: Intel Страницы: 54
Abus TVAC21000 User Manual preview
TVAC21000
Бренд: Abus Страницы: 98
Ublox USB-ANNA-B4 User Manual preview
USB-ANNA-B4
Бренд: Ublox Страницы: 11

Бренды по названию

Популярные бренды

Загрузить еще бренды