Intellian T240CK Скачать руководство пользователя страница 137

Страница: 137 / 160

137

Aptus WEB

No.

Item

Description

Ship Setting

Set the ship information and find antenna angle.

GPS

Set GPS information.
- Longitude (East/West)
- Latitude (North/South)

Bow Offset

Set Bow Offset if needed.

Heading Device

Set ship’s heading device (NONE, NMEA, NMEA2000,
Ground Test) and ship’s heading information

Antenna Angle

Find the current antenna angles and skew angle in relation to
the longitude (orbit position) of the antenna's current GPS.
Click 'Find Angles & Skew Antenna GPS' button.

WARNING:

Enter the SETUP mode for configuration. Tick the checkbox before

modifying the settings. After configuration, click ‘Set ...’ button to submit the settings.

Ship Setting

Antenna Settings

Содержание T240CK

































































































































































Результаты поиска

Содержание T240CK

Отзывы:

Похожие инструкции для T240CK

Бренды по названию

Популярные бренды

Intellian T240CK, Инструкция по установке и эксплуатации

Результаты поиска

Содержание T240CK

Отзывы:

Похожие инструкции для T240CK

Бренды по названию

Популярные бренды