Intel Xeon E5-2400 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 100

Intel Xeon E5-2400 Скачать руководство пользователя страница 24

Independent Loading Mechanism (ILM) and Back Plate

24

Intel® Xeon® Processor E5-2400 Product Family

Thermal/Mechanical Design Guide

3.1.2

ILM Back Plate Design Overview

The unified back plate consists of a flat steel back plate with threaded studs for ILM
attach, and internally threaded nuts for heatsink attach. The threaded studs have a
smooth surface feature that provides alignment for the back plate to the motherboard
for proper assembly of the ILM around the socket. A clearance hole is located at the
center of the plate to allow access to test points and backside capacitors. An additional
cut-out on two sides provides clearance for backside voltage regulator components. An
insulator is pre-applied. To stay within the temperature limit of the insulator, remove
the back plate prior to board component rework.

3.1.3

Durability

The ILM durability requirement is 30 processor cycles. 1 processor cycle = install
processor, close load plate, latch load lever, unlatch load lever, open load plate.

The ILM durability requirement is 6 assembly cycles. See

for assembly

procedure. 1 assembly cycle = fasten the ILM assembly to the back plate with the four
captive screws, torque to 9 ± 1 inch-pounds, unfasten ILM assembly from the back
plate.

Figure 3-1. ILM Assembly

«
...
22
23
24
25
26
...
»

Содержание Xeon E5-2400





































































































Отзывы:

Нет отзывов