Intel I7-900 DEKSTOP SPECIFICATION страница 48 Скачать руководство пользователя

Страница: 48 / 98

Register Description

Datasheet

CHANNEL0_ACTIVE
When set, indicate MC channel 0 is active. This bit is controlled (set/reset) by

software only. This bit is required to be set for any active channel when

INIT_DONE is set by software. Channel 0 AND Channel 1 active must both be

set for a lockstep or mirrored pair.

INIT_DONE
MC initialize complete signal. Setting this bit will exit the training mode of the

Integrated Memory Controller and begin normal operation including all

enabled maintenance operations. Any CHANNNEL_ACTIVE bits not set when

writing a 1 to INIT_DONE will cause the corresponding channel to be

disabled.

DIVBY3EN
Divide By 3 enable. When set, MAD would use the longer pipeline for

transactions that are 3 or 6 way interleaved and shorter pipeline for all other

transactions. The SAG registers must be appropriately programmed as well.

CHANNELRESET2
Reset only the state within the channel. Equivalent to pulling warm reset for

that channel.

CHANNELRESET1
Reset only the state within the channel. Equivalent to pulling warm reset for

that channel.

CHANNELRESET0
Reset only the state within the channel. Equivalent to pulling warm reset for

that channel.

AUTOPRECHARGE.
Autoprecharge enable. This bit should be set with the closed page bit. If it is

not set with closed page, address decode will be done without setting the

autoprecharge bit.

ECCEN: ECC Enable
ECC Checking enables. When this bit is set in lockstep mode the ECC

checking is for the x8 SDDC. ECCEN without Lockstep enables the x4 SDDC

ECC checking.

CLOSED_PAGE
When set, the MC supports a Closed Page policy. The default is Open Page

but BIOS should always configure this bit.

Device:

Function: 0

Offset:

48h

Access as a Dword

Содержание I7-900 DEKSTOP SPECIFICATION



































































































Результаты поиска

Содержание I7-900 DEKSTOP SPECIFICATION

Отзывы:

Похожие инструкции для I7-900 DEKSTOP SPECIFICATION

Бренды по названию

Популярные бренды

Intel I7-900 DEKSTOP SPECIFICATION, Техническое описание

Результаты поиска

Содержание I7-900 DEKSTOP SPECIFICATION

Отзывы:

Похожие инструкции для I7-900 DEKSTOP SPECIFICATION

Бренды по названию

Популярные бренды