Intel I7-900 DEKSTOP SPECIFICATION страница 71 Скачать руководство пользователя

Страница: 71 / 98

Datasheet

Register Description

2.10.14 MC_CHANNEL_0_CKE_TIMING

MC_CHANNEL_1_CKE_TIMING

MC_CHANNEL_2_CKE_TIMING

This register contains parameters that specify the CKE timings. All units are in DCLK.

2.10.15 MC_CHANNEL_0_ZQ_TIMING

MC_CHANNEL_1_ZQ_TIMING

MC_CHANNEL_2_ZQ_TIMING

This register contains parameters that specify ZQ timing. All units are DCLK unless
otherwise specified. The register encodings are specified where applicable.

Device:

4, 5, 6

Function: 0

Offset:

90h

Access as a Dword

Bit

Type

Reset

Value

Description

31:24

tRANKIDLE.
Rank will go into powerdown after it has been idle for the specified number of

dclks. tRANKIDLE covers max(txxxPDEN). Minimum value is tWRAPDEN. If CKE

is being shared between ranks then both ranks must be idle for this amount of

time. A Power Down Entry command will be requested for a rank after this

number of DCLKs if no request to the rank is in the MC.

23:21

tXP.
Minimum delay from exit power down with DLL and any valid command. Exit

Precharge Power Down with DLL frozen to commands not requiring a locked

DLL. Slow exit precharge powerdown is not supported.

20:11

tXSDLL.
Minimum delay between the exit of self refresh and commands that require a

locked DLL.

10:3

tXS.
Minimum delay between the exit of self refresh and commands not requiring a

DLL.

2:0

tCKE.
CKE minimum pulse width.

Device:

4, 5, 6

Function: 0

Offset:

94h

Access as a Dword

Bit

Type

Reset

Value

Description

Parallel_ZQ.
Enable ZQ calibration to different ranks in parallel.

tZQenable.
Enable the issuing of periodic ZQCS calibration commands.

28:8

16410

ZQ_Interval.
Nominal interval between periodic ZQ calibration in increments of tREFI.

7:5

tZQCS.
This field specifies ZQCS cycles in increments of 16. This is the minimum delay

between ZQCS and any other command. This register should be programmed to

at least 64/16=4='100' to conform to the DDR3 specification.

4:0

tZQInit.
This field specifies ZQInit cycles in increments of 32. This is the minimum delay

between ZQCL and any other command. This register should be programmed to

at least 512/32=16='10000' to conform to the DDR3 specification.

Содержание I7-900 DEKSTOP SPECIFICATION



































































































Результаты поиска

Содержание I7-900 DEKSTOP SPECIFICATION

Отзывы:

Похожие инструкции для I7-900 DEKSTOP SPECIFICATION

Бренды по названию

Популярные бренды

Intel I7-900 DEKSTOP SPECIFICATION, Техническое описание

Результаты поиска

Содержание I7-900 DEKSTOP SPECIFICATION

Отзывы:

Похожие инструкции для I7-900 DEKSTOP SPECIFICATION

Бренды по названию

Популярные бренды