Intel DB85FL Скачать руководство пользователя страница 40

Страница: 40 / 84

Intel Desktop Board DB85FL Technical Product Specification

2.2

Connectors and Headers

CAUTION

Only the following connectors and headers have overcurrent protection: back panel

and front panel USB.
The other internal connectors and headers are not overcurrent protected and should

connect only to devices inside the computer’s chassis, such as fans and internal

peripherals. Do not use these connectors or headers to power devices external to the

computer’s chassis. A fault in the load presented by the external devices could cause

damage to the computer, the power cable, and the external devices themselves.
Furthermore, improper connection of USB header single wire connectors may

eventually overload the overcurrent protection and cause damage to the board.

This section describes the board’s connectors. The connectors can be divided into

these groups:

•

Back panel I/O connectors

•

Component-side connectors and headers (see page 42)

Содержание DB85FL





















































































Результаты поиска

Содержание DB85FL

Отзывы:

Похожие инструкции для DB85FL

Бренды по названию

Популярные бренды

Intel DB85FL, Спецификация

Результаты поиска

Содержание DB85FL

Отзывы:

Похожие инструкции для DB85FL

Бренды по названию

Популярные бренды