Intel CELERON PROCESSOR E3000 - THERMAL AND MECHANICAL DESIGN страница 17 Скачать руководство пользователя | Manualshive

Страница: 17 / 126

background image

Processor Thermal/Mechanical Information

Thermal and Mechanical Design Guidelines

17

Figure 2-2. Processor Case Temperature Measurement Location

37.5 mm

Measure T

C

at this point

(geometric center of the package)

37.

5 m

m

37.5 mm

Measure T

C

at this point

(geometric center of the package)

37.

5 m

m

2.2.2

Thermal Profile

The Thermal Profile defines the maximum case temperature as a function of processor
power dissipation. Refer to the datasheet for the further information.

2.2.3

Thermal Solution Design Requirements

While the thermal profile provides flexibility for ATX /BTX thermal design based on its
intended target thermal environment, thermal solutions that are intended to function
in a multitude of systems and environments need to be designed for the worst-case
thermal environment. The majority of ATX /BTX platforms are targeted to function in
an environment that will have up to a 35° C ambient temperature external to the
system.

For ATX platforms, an active air-cooled design, assumed be used in ATX Chassis, with
a fan installed at the top of the heatsink equivalent to the reference design (see
Chapter 6) should be designed to manage the processor TDP at an inlet temperature
of 35° C + 5°C = 40° C.

For BTX platforms, a front-to-back cooling design equivalent to Intel BTX TMA Type II
reference design (see the Chapter 5) should be designed to manage the processor
TDP at an inlet temperature of 35° C + 0.5° C = 35.5° C.

The slope of the thermal profile was established assuming a generational improvement
in thermal solution performance of the Intel reference design. For an example of Intel
Core™2 Duo Processor E8000 series with 6 MB in ATX platform, its improvement is
about 15% over the Intel reference design (E18764-001). This performance is
expressed as the slope on the thermal profile and can be thought of as the thermal

resistance of the heatsink attached to the processor,

Ψ

CA

(Refer to Section 3.1). The

intercept on the thermal profile assumes a maximum ambient operating condition that
is consistent with the available chassis solutions.

«
...
15
16
17
18
19
...
»

Содержание CELERON PROCESSOR E3000 - THERMAL AND MECHANICAL DESIGN































































































































Отзывы:

Нет отзывов

Похожие инструкции для CELERON PROCESSOR E3000 - THERMAL AND MECHANICAL DESIGN

Express EtherNetwork DFE-670TXD

Бренд: D-Link Страницы: 4

Бренд: DAD Страницы: 36

Бренд: D-Link Страницы: 2

Бренд: Delta Tau Страницы: 74

Storagelibrary T24

Бренд: Tandberg Data Страницы: 28

Бренд: National Instruments Страницы: 8

Easy Tool-ID BSG TID-05-T30-00-005

Бренд: Balluff Страницы: 46

memonizerWORKSTATION

Бренд: MEMON Страницы: 2

Бренд: Uniden Страницы: 5

Бренд: Unex Страницы: 27

Masterliquid ML240L RGB

Бренд: Cooler Master Страницы: 18

Data Capture Board CLC-CAPT-PCASM

Бренд: National Semiconductor Страницы: 15

Бренд: IEI Technology Страницы: 146

Бренд: Williams Sound Страницы: 2

Бренд: Alpine Страницы: 17

Бренд: Hama Страницы: 10

X-NUCLEO-GFX01M Series

Бренд: ST Страницы: 31

Бренд: Westlock Controls Corporation Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды