manualshive.com logo in svg

Intel BX80619I73820, Руководство по конструкции, Страница: 107 / 124

Поделиться
Скачать
Intel BX80619I73820 Скачать руководство пользователя страница 107

Thermal/Mechanical Specifications and Design Guide

107

Quality and Reliability Requirements

9.2.2

Post-Test Pass Criteria Examples

The post-test pass criteria examples are:

1. No significant physical damage to the heatsink and retention hardware. 
2. Heatsink remains seated and its bottom remains mated flat against the IHS 

surface. No visible gap between the heatsink base and processor IHS. No visible tilt 
of the heatsink with respect to the retention hardware.

3. No signs of physical damage on baseboard surface due to impact of heatsink.
4. No visible physical damage to the processor package.
5. Successful BIOS/Processor/memory test of post-test samples.
6. Thermal compliance testing to demonstrate that the case temperature specification 

can be met.

9.2.3

Recommended BIOS/Processor/Memory Test Procedures

This test is to ensure proper operation of the product before and after environmental 

stresses, with the thermal mechanical enabling components assembled. The test shall 

be conducted on a fully operational baseboard that has not been exposed to any 
battery of tests prior to the test being considered. 

Testing setup should include the following components, properly assembled and/or 

connected:

• Appropriate system baseboard.
• Processor and memory.
• All enabling components, including socket and thermal solution parts.

The pass criterion is that the system under test shall successfully complete the 

checking of BIOS, basic processor functions and memory, without any errors. 

Intel PC 

Diags 

is an example of software that can be utilized for this test.

9.3

Material and Recycling Requirements

Material shall be resistant to fungal growth. Examples of non-resistant materials 
include cellulose materials, animal and vegetable based adhesives, grease, oils, and 

many hydrocarbons. Synthetic materials such as PVC formulations, certain 

polyurethane compositions (for example, polyester and some polyethers), plastics 
which contain organic fillers of laminating materials, paints, and varnishes also are 

susceptible to fungal growth. If materials are not fungal growth resistant, then MIL-

STD-810E, Method 508.4 must be performed to determine material performance. 
Cadmium shall not be used in the painting or plating of the socket.CFCs and HFCs shall 

not be used in manufacturing the socket. 

Any plastic component exceeding 25 gm should be recyclable per the European Blue 
Angel recycling standards. 

Supplier is responsible for complying with industry standards regarding environmental 

care as well as with the specific standards required per Supplier's region. More 
specifically, Supplier is responsible for compliance with the European regulations 

related to restrictions on the use of Lead and Bromine containing flame-retardants. 
Legislation varies by geography, European Union (RoHS/WEEE), China, California, and 

so forth.

Содержание BX80619I73820





























































































































Отзывы:

Нет отзывов