Intel BX80562Q6600 - Core 2 Quad 2.4 GHz Processor Скачать руководство пользователя страница 63

Страница: 63 / 69

Errata

Intel

Core™2 Extreme Quad-Core Processor QX6000

Sequence and

Intel

Core™2 Quad Processor Q6000

Sequence

Specification Update

in NMIs not being blocked after a VM-entry failure during or after loading

guest state.

Implication:

VM-entry failures that cause NMIs to become unblocked may cause the

processor to deliver an NMI to software that is not prepared for it.

Workaround:

VMM software should configure the virtual-machine control structure (VMCS)

so that VM-entry failures do not occur.

Status:

For the steppings affected, see the Summary Tables of Changes.

AK121.

Benign Exception after a Double Fault May Not Cause a Triple Fault

Shutdown

Problem:

According to the

Intel

64 and IA-32 Architectures Software Developer’s

Manual, Volume 3A

, “Exception and Interrupt Reference”, if another

exception occurs while attempting to call the double-fault handler, the

processor enters shutdown mode. However due to this erratum, only

Contributory Exceptions and Page Faults will cause a triple fault shutdown,

whereas a benign exception may not.

Implication:

If a benign exception occurs while attempting to call the double-fault

handler, the processor may hang or may handle the benign exception. Intel

has not observed this erratum with any commercially available software.

Workaround:

None identified.

Status:

For the steppings affected, see the Summary Tables of Changes.

AK122.

IA32_MC1_STATUS MSR Bit[60] Does Not Reflect Machine Check

Error Reporting Enable Correctly

Problem:

IA32_MC1_STATUS MSR (405H) bit[60] (EN- Error Enabled) is supposed to

indicate whether the enable bit in the IA32_MC1_CTL MSR (404H) was set at

the time of the last update to the IA32_MC1_STATUS MSR. Due to this

erratum, IA32_MC1_STATUS MSR bit[60] instead reports the current value of

the IA32_MC1_CTL MSR enable bit.

Implication:

IA32_MC1_STATUS MSR bit [60] may not reflect the correct state of the

enable bit in the IA32_MC1_CTL MSR at the time of the last update.

Workaround:

None identified.

Status:

For the steppings affected, see the Summary Tables of Changes.

AK123.

A VM Exit Due to a Fault While Delivering a Software Interrupt May

Save Incorrect Data into the VMCS

Problem:

If a fault occurs during delivery of a software interrupt (INTn) in virtual-8086

mode when virtual mode extensions are in effect and that fault causes a VM

exit, incorrect data may be saved into the VMCS. Specifically, information

about the software interrupt may not be reported in the IDT-vectoring

Содержание BX80562Q6600 - Core 2 Quad 2.4 GHz Processor






































































Результаты поиска

Содержание BX80562Q6600 - Core 2 Quad 2.4 GHz Processor

Отзывы:

Похожие инструкции для BX80562Q6600 - Core 2 Quad 2.4 GHz Processor

Бренды по названию

Популярные бренды

Intel BX80562Q6600 - Core 2 Quad 2.4 GHz Processor, Спецификация

Результаты поиска

Содержание BX80562Q6600 - Core 2 Quad 2.4 GHz Processor

Отзывы:

Похожие инструкции для BX80562Q6600 - Core 2 Quad 2.4 GHz Processor

Бренды по названию

Популярные бренды