Intel 848P Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 35

background image

Reference Thermal Solution

R

Intel

®

848P Chipset Thermal Design Guide

21

4

Reference Thermal Solution

The Wave Solder Heatsink (WSHS) is the reference component thermal solution for the MCH. This
chapter provides detailed information on operating environment assumptions, heatsink
manufacturing, heatsink rework, and mechanical reliability requirements.

4.1 Operating

Environment

An airflow speed of 0.76 m/s [150 lfm] is assumed to be present 25 mm [1 in] in front of the heatsink
air inlet side of the attached reference thermal solution. The potential for increased airflow speeds
may be realized by ensuring that airflow from the processor heatsink fan exhausts in the direction of
the MCH heatsink. This can be achieved by orienting the processor heatsink fins perpendicular to the
MCH heatsink face or by using a heatsink with omni directional airflow
(e.g., a radial fin or “X” pattern heatsink). Figure 8 illustrates the fin orientation of a straight fin
heatsink that provides airflow to the MCH heatsink. In addition, MCH board placement should
ensure that the MCH heatsink is within the air exhaust area of the processor heatsink.

Note that heatsink orientation alone does not guarantee that 0.76 m/s [150 lfm] airflow speed
will be achieved.

The system integrator should use analytical or experimental means to determine

whether a system design provides adequate airflow speed for a particular MCH heatsink.

Figure 8. Processor Heatsink Orientation to Provide Airflow to MCH Heatsink

Airflow Direction

Processor Heatsink

(Fan Not Shown)

(G)MCH Heatsink

Top View

proc_airflow

Other methods exist for providing airflow to the MCH heatsink, including the use of system fans
and/or ducting, or the use of an attached fan (active heatsink).

«
...
19
20
21
22
23
...
»

Содержание 848P




































Отзывы:

Нет отзывов

Похожие инструкции для 848P

Бренд: Aaeon Страницы: 76

Бренд: Manfrotto Страницы: 16

Бренд: Jetline Страницы: 58

Бренд: Bard Страницы: 8

Бренд: Bardiani Valvole Страницы: 35

Бренд: Danfoss Страницы: 85

VLT Decentral FCD 300

Бренд: Danfoss Страницы: 112

Бренд: Danfoss Страницы: 4

VLT 6000 series

Бренд: Danfoss Страницы: 27

Бренд: Danfoss Страницы: 16

Бренд: Danfoss Страницы: 20

ADAP-KOOL AK-PC 781

Бренд: Danfoss Страницы: 14

Бренд: Danfoss Страницы: 12

Бренд: Danfoss Страницы: 12

vlt soft starter mcd 500

Бренд: Danfoss Страницы: 96

Бренд: ZKTeco Страницы: 8

Бренд: EasyIO Страницы: 18

Бренд: Rain Bird Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды