Intel 413808 I/O Скачать руководство пользователя страница 50

Страница: 50 / 824

Intel

413808 and 413812—Address Translation Unit (PCI-X)

Intel

413808 and 413812 I/O Controllers in TPER Mode

Developer’s Manual

October 2007

Order Number: 317805-001US

2.0

Address Translation Unit (PCI-X)

This chapter describes the operation modes, setup, and implementation of the module

which interfaces between the PCI bus and the Intel

413808 and 413812 I/O

Controllers in TPER Mode (4138xx) internal bus.

2.1

Overview

As indicated in

Figure 3

, the Address Translation Unit (ATU) — the interface between

the PCI bus and the on-chip internal bus — consists of the Address Translation Unit

(ATU) and the Expansion ROM Unit.
The ATU supports both inbound and outbound address translation. The ATU provides

access between the PCI bus and the 4138xx internal bus.
Transactions initiated on the PCI bus and targeted at the 4138xx internal bus are

referred to as inbound transactions (PCI to internal bus). Transactions initiated on the

4138xx internal bus and targeted at the PCI bus are referred to as outbound

transactions (internal bus to PCI). The ATU accepts multiple inbound or outbound

transactions and processes them simultaneously.
During inbound transactions, the ATU converts PCI addresses (initiated by a PCI bus

master) to Internal Bus Addresses and initiates the data transfer on the 4138xx

internal bus. During outbound transactions, the ATU converts internal bus addresses to

PCI addresses and initiates the data transfer on the PCI bus.
The Expansion ROM provides the PCI mechanism for downloading device/board driver

code during system boot sequence. It consists of a separate inbound address range

which accesses a Flash EPROM device connected through the 4138xx memory

controller. Refer to the PCI Local Bus Specification, Revision 2.3 for details of Expansion

ROM usage.
The Address Translation Unit and the Expansion ROM Translation Unit represent a single

function of the multi-function 4138xx PCI device.
The ATU supports the following PCI operating modes and bus widths delivering up to

2133 Mbytes/sec of bandwidth:

— Conventional Modes: PCI 33, PCI 66

— PCI-X Modes: Mode 1 (PCI-X 66, PCI-X 133), Mode 2 (PCI-X 266)

— Bus Widths: 64-bit, 32-bit

In Mode 2, all transaction phases are ECC protected (when enabled). In the remaining

PCI-X and Conventional modes supported by 4138xx, all transaction phases are parity

protected (when enabled).
On the internal interface, the ATU implements the 4138xx internal bus protocol which

provides for a maximum of 4800 Mbytes/sec of bandwidth.

3. PCIX is not supported in TPER mode.

Содержание 413808 I/O

























































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 413808 I/O

Отзывы:

Бренды по названию

Популярные бренды

Intel 413808 I/O, Руководство разработчика

Результаты поиска

Содержание 413808 I/O

Отзывы:

Бренды по названию

Популярные бренды