manualshive.com logo in svg

Intel 413808 I/O, Руководство разработчика

Поделиться
Скачать
Intel 413808 I/O Скачать руководство пользователя страница 127

Intel

®

 413808 and 413812 I/O Controllers in TPER Mode

October 2007

Developer’s Manual

Order Number: 317805-001US

127

Address Translation Unit (PCI-X)—Intel

®

 413808 and 413812

2.10

Vital Product Data

Vital Product Data (VPD) provides detailed information to the system regarding the 

hardware, software and microcode elements of a device. This information may include 

Part Number, Serial Number or other detailed information. This information resides on a 

non-volatile storage device (i.e., Flash Memory) attached to the 4138xx. In addition 

VPD also provides a mechanism for storing information such as performance or failure 

data on the device being monitored.
Support of VPD involves the implementation of the VPD Extended Capabilities List Item 

in the Primary ATU. The VPD Extended capabilities header consists of five registers, the 

“VPD Capability Identifier Register - VPD_Cap_ID” on page 185

, the 

“VPD Next Item 

Pointer Register - VPD_Next_Item_Ptr” on page 185

, the 

“VPD Address Register - 

VPDAR” on page 186

, and the 

“VPD Data Register - VPDDR” on page 186

. 

Scheduled by Intel XScale

®

 processor interrupts, the 4138xx may be used to retrieve 

or store VPD information through the VPD extended capabilities list item.
Please consult Appendix I of the PCI Local Bus Specification, Revision 2.3 for the 

definitions of compliant VPD format.

2.10.1

Configuring Vital Product Data Operation

By default, the 4138xx VPD functionality is not configured for operation. Specifically, 

the VPD Extended Capabilities List Item is not discovered during a PCI bus scan and the 

ATUs VPD interrupt status bit in the 

“ATU Interrupt Status Register - ATUISR” on 

page 181

 is masked by the 

“ATU Interrupt Mask Register - ATUIMR” on page 183

. The 

following steps should be followed to properly configure the 4138xx support for VPD:

1. The 4138xx must be strapped to Retry Type 0 Configuration cycles following the 

deassertion of 

P_RST#

. Enabling this configuration cycle retry mechanism insures 

that the Intel XScale

®

 processor can make the VPD Extended Capabilities List Item 

visible before the system configures the 4138xx. The configuration retry 

mechanism is controlled through bit 2 of the 

“PCI Configuration and Status Register 

- PCSR” on page 178

. 

2. When the configuration retry mechanism is strapped enabled as described in step 

1, typically, the 4138xx would also be strapped such that the Intel XScale

®

 

processor would immediately boot following the deassertion of 

P_RST#

 (bit 1 of 

the PCSR), though this is not required.

3. The Intel XScale

®

 processor writes E8H to the 

“PCI-X Next Item Pointer Register - 

PCI-X_Next_Item_Ptr” on page 191

. This links the PCI-X Capabilities List Item to 

the VPD Capabilities List Item.

4. The Intel XScale

®

 processor clears bit 12 of the ATUIMR to enable the ATUs VPD 

interrupt status bit.

Содержание 413808 I/O

























































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды