manualshive.com logo in svg

Intel 413808 I/O, Руководство разработчика

Поделиться
Скачать
Intel 413808 I/O Скачать руководство пользователя страница 204

Intel

®

 413808 and 413812—Address Translation Unit (PCI-X)

Intel

®

 413808 and 413812 I/O Controllers in TPER Mode

Developer’s Manual

October 2007

204

Order Number: 317805-001US

2.14.64 Inbound ATU Base Address Register 3 - IABAR3

The Inbound ATU Base Address Register 3 (IABAR3) together with the Inbound ATU 

Upper Base Address Register 3 (IAUBAR3) defines the block of memory addresses 

where the inbound translation window 3 begins. The inbound ATU decodes and 

forwards the bus request to the 4138xx internal bus with a translated address to map 

into 4138xx local memory. The IABAR3 and IAUBAR3 define the base address and 

describe the required memory block size; see 

Section 2.14.23, “Determining Block 

Sizes for Base Address Registers” on page 164

. Bits 31 through 12 of the IABAR3 is 

either read/write bits or read only with a value of 0 depending on the value located 

within the IALR3. This configuration allows the IABAR3 to be programmed per PCI Local 

Bus Specification, Revision 2.3.
The programmed value within the base address register must comply with the PCI 

programming requirements for address alignment. Refer to the PCI Local Bus 

Specification, Revision 2.3 for additional information on programming base address 

registers.

Note:

Since IABAR3 does not appear in the standard PCI configuration header space (offsets 

00H - 3CH), IABAR3 is not configured by the host during normal system initialization.

Warning:

When a non-zero value is not written to IALR3, the user should not set either the 

Prefetchable Indicator or the Type Indicator for 64 bit addressability. This is the default 

for IABAR3. Assuming a non-zero value is written to IALR3, the user may set the 

Prefetchable Indicator or the Type Indicator:

a. Since non prefetchable memory windows can never be placed above the 4 Gbyte 

address boundary, when the Prefetchable Indicator is not set, the user should 

also leave the Type Indicator set for 32 bit addressability. This is the default for 

IABAR3.

b. For compliance to the PCI-X Protocol Addendum to the PCI Local Bus 

Specification, Revision 2.0, when the Prefetchable Indicator is set, the user 

should also set the Type Indicator for 64 bit addressability.

Table 91. Inbound ATU Base Address Register 3 - IABAR3

Bit

Default

Description

31:12

00000H

Translation Base Address 3 - These bits define the actual location the translation function is to respond 

to when addressed from the PCI bus. 

11:04

00H

Reserved.

03

0

2

Prefetchable Indicator - When set, defines the memory space as prefetchable.

02:01

00

2

Type Indicator - Defines the width of the addressability for this memory window:

00 - Memory Window is locatable anywhere in 32 bit address space

10 - Memory Window is locatable anywhere in 64 bit address space

00

0

2

Memory Space Indicator - This bit field describes memory or I/O space base address. The ATU does not 

occupy I/O space, thus this bit must be zero.

PCI

IOP

Attributes

Attributes

28

24

20

16

12

8

4

0

31

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rw

rv

rv

rv

rv

rv

rv

rv

rv

rv

rv

rv

rv

rv

rv

rv

rv

rw

ro

rw

ro

ro

ro

ro

ro

Attribute Legend:

RV = Reserved

PR = Preserved

RS = Read/Set

RW = Read/Write

RC = Read Clear

RO = Read Only

NA = Not Accessible

 Register Offset

+200H

Содержание 413808 I/O

























































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды