Intel 413808 I/O Скачать руководство пользователя страница 3

Страница: 3 / 824

Intel

413808 and 413812 I/O Controllers in TPER Mode

October 2007

Developer’s Manual

Order Number: 317805-001US

Contents—Intel

413808 and 413812

Contents

1.0 Introduction...............................................................................................................36

1.1 Design-in Considerations....................................................................................38

1.1.1 Software ...............................................................................................39

1.2 Documentation References ................................................................................. 40

1.3 About This Document......................................................................................... 41

1.3.1 How To Read This Document ................................................................... 41

1.3.2 Other Relevant Documents ...................................................................... 41

1.4 About the Intel

413808 and 413812 I/O Controllers in TPER Mode ......................... 42

1.5 Intel

413808 and 413812 I/O Controllers in TPER Mode Features...........................44

1.5.1 Host Interface........................................................................................ 44

1.5.2 Intel XScale

Processor .......................................................................... 44

1.5.3 Internal Busses...................................................................................... 45

1.5.4 Application DMA Controller ...................................................................... 45

1.5.5 Address Translation Unit .........................................................................45

1.5.6 Messaging Unit ...................................................................................... 46

1.5.7 DDR Memory Controller........................................................................... 46

1.5.8 Peripheral Bus Interface.......................................................................... 46

1.5.9 Performance Monitoring Unit....................................................................46

1.5.10 I

C Bus Interface Unit............................................................................. 46

1.5.11 UART Unit ............................................................................................. 46

1.5.12 Interrupt Controller Unit.......................................................................... 46

1.5.13 Internal Bus System Controller.................................................................47

1.5.14 Inter-Processor Communication................................................................ 47

1.5.15 Inter-Processor Messaging Unit ................................................................ 47

1.5.16 Timers.................................................................................................. 47

1.5.17 GPIO .................................................................................................... 47

1.5.18 FSENG.................................................................................................. 47

1.6 Terminology and Conventions ............................................................................. 48

1.6.1 Representing Numbers............................................................................48

1.6.2 Fields ................................................................................................... 48

1.6.3 Specifying Bit and Signal Values............................................................... 49

1.6.4 Signal Name Conventions........................................................................ 49

1.6.5 Terminology .......................................................................................... 49

2.0 Address Translation Unit (PCI-X) .................................................................................. 50

2.1 Overview ......................................................................................................... 50

2.2 ATU Address Translation ....................................................................................53

2.2.1 Inbound Transactions ............................................................................. 55

2.2.1.1 Inbound Address Translation ......................................................56

2.2.1.2 Inbound Write Transaction .........................................................59

2.2.1.3 Inbound Read Transaction.......................................................... 61

2.2.1.4 Inbound Configuration Cycle Translation ......................................64

2.2.1.5 Discard Timers .........................................................................66

2.2.2 Outbound Transactions- Single Address Cycle (SAC) Internal Bus Transactions...

2.2.2.1 Outbound Address Translation - Internal Bus Transactions.............. 68

2.2.2.2 Outbound Address Translation Windows....................................... 69

2.2.3 Outbound Write Transaction ....................................................................72

2.2.4 Outbound Read Transaction..................................................................... 74

2.2.5 Outbound Configuration Cycle Translation.................................................. 75

2.2.5.1 PCI-X Mode 1 Considerations for Outbound Configuration Cycles ..... 75

2.2.5.2 PCI-X Mode 2 Considerations for Outbound Configuration Cycles ..... 76

2.2.5.3 Outbound Configuration Cycle Error Conditions ............................. 76

Содержание 413808 I/O

























































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 413808 I/O

Отзывы:

Бренды по названию

Популярные бренды

Intel 413808 I/O, Руководство разработчика

Результаты поиска

Содержание 413808 I/O

Отзывы:

Бренды по названию

Популярные бренды