128
Advanced Setup
—Continued
Tuner
■
AM Freq Step (on some models)
See “AM Frequency Step Setup (on some models)” on
page 59.
■
Satellite Radio (on North American model)
If you connect an XM Satellite Radio antenna or SIRIUS
Satellite Radio antenna to the AV receiver (both sold
separately), set this setting to XM or SIRIUS respec-
tively. If you connect both types of antenna, select
XM/SIRIUS. Otherwise, select None (See
pages 76–90).
Analog Multich
■
Subwoofer Input Sensitivity
Some DVD players output the LFE channel from their
analog subwoofer output at 15 dB higher than normal.
With this setting, you can change the AV receiver’s sub-
woofer sensitivity to match your DVD player. Note that
this setting only affects signals connected to the AV
receiver’s MULTI CH: SUBWOOFER jack.
You can select 0 dB, 5 dB, 10 dB, or 15 dB.
If you find that your subwoofer is too loud, try the 10 dB
or 15 dB setting.
HDMI
■
Audio TV Out
This setting determines whether audio received by an
HDMI input is output by the HDMI outputs. You may
want to change this setting to “On” if your TV is con-
nected to an HDMI output and you want to listen to
audio from an HDMI component through your TV’s
speakers. Normally, it should be set to “Off”.
Off:
HDMI audio is not output (default).
On:
HDMI audio is output.
Notes:
• If “On” is selected and the signal can be output by the
TV, the AV receiver will output no sound through its
speakers.
• When “TV Control” is enabled, this setting is set to
“Auto”.
• With some TVs and input signals, no sound may be
output even if “On” is selected.
• When the “Audio TV Out” setting is set to “On”, or
“TV Control” is set to “Enable” and you’re listening
through your TV’s speakers (see page 39), if you turn
up the AV receiver’s volume control, the sound will be
output by the AV receiver’s speakers. To stop the AV
receiver’s speakers producing sound, change the set-
tings, change your TV’s settings, or turn down the AV
receiver’s volume.
■
Lip Sync
The Lip Sync function can automatically synchronize
HDMI audio and video that’s gotten out of sync due to
the complex digital video processing being performed by
your HDMI-compatible TV. With HDMI Lip Sync, the
audio delay required to synchronize the audio and video
is calculated and applied automatically by the AV
receiver.
Disable:
HDMI lip sync disabled (default).
Enable:
HDMI lip sync enabled.
Notes:
• This function works only if your HDMI-compatible
TV supports HDMI Lip Sync.
• You can check the amount of delay being applied by
the HDMI Lip Sync function on the “A/V Sync”
screen (see page 120).
■
x.v.Color
If your HDMI source and HDMI-compatible TV both
support the “x.v.Color”, you can enable “x.v.Color” on
the AV receiver with this setting.
Disable:
“x.v.Color” disabled (default).
Enable:
“x.v.Color” enabled.
Notes:
• If the color is unnatural when “x.v.Color” is set to
“Enable”, change the setting to
“Disable”
.
• Refer to the connected component’s instruction man-
ual for details.
■
Control
This function allows
-compatible components
connected via HDMI to be controlled with the AV
receiver.
Notes:
•
, which stands for Remote Interactive over
HDMI, is the name of the system control function
found on Onkyo components. The AV receiver can be
used with CEC (Consumer Electronics Control),
which allows system control over HDMI and is part of
the HDMI standard. CEC provides interoperability
between various components, however, operation with
components other than
-compatible compo-
nents cannot be guaranteed.
• Set to
“Disable”
when a connected piece of equipment
is not compatible or it is unclear whether the equip-
ment is compatible or not.
• If movement is unnatural when set to
“Enable”
, change
the setting to
“Disable”
.
• Refer to the connected component’s instruction man-
ual for details.
Disable:
disabled (default).
Enable:
enabled.
Содержание DTR-8.9
Страница 1: ...DTR 8 9 Instruction Manual AV Receiver DTR 9 9...
Страница 161: ...161 Memo...
