Integra DTR-60.5, Инструкция по эксплуатации

Страница: 69 / 112

Advanced Operations
En-69 Operating procedure (
➔
page 59 )
Theater-Dimensional
■
Listening Angle
`
Wide :
Select if the listening angle is greater than 30
degrees.
`
Narrow :
Select if the listening angle is less than 30
degrees.
With this setting, you can optimize the Theater-
Dimensional listening mode by specifying the angle of
the front left and right speakers relative to the
listening position. Ideally, the front left and right
speakers should be equidistant from the listening
position and at an angle close to one of the two
available settings.
Note
• For best results, we recommend setting “
Narrow
” to 20°
and “ Wide ” to 40°.
LFE Level
■
Dolby Digital
*1
, DTS
*2
, Multich PCM, Dolby
TrueHD, DTS-HD Master Audio, DSD
*3
`
– Q dB , –20dB , –10dB , or 0dB
With these settings, you can set the level of the LFE
(Low Frequency Effects) channel individually for each
input sources.
If you find that low-frequency effects are too loud
when using one of these sources, change the setting
to –20 dB or –
Q
dB.
*1 Dolby Digital and Dolby Digital Plus sources
*2
DTS and DTS-HD High Resolution sources
*3 DSD (Super Audio CD) sources
Sound Program Edit
■
Sound Program
`
Stereo Source 1 , Stereo Source 2 , Stereo
Source 3 , Multich Source 1 , Multich Source 2 ,
Multich Source 3
When playing back different content types on the
same source, or when listening to a single content
type on different sources, you can pre-register the
settings that best suit each content in “
Sound
Program ”. The registered settings can then be called
up and modified in one set. Use “ Sound Program
Edit ” to register and modify a combination of settings.
Tip
• To select the registered settings, see “ Sound Program ”
(
➔
page 56 ).
■
Listening Mode
You can assign a default listening mode that will be
selected automatically when you select the sound
program.
The “
Last Valid ” option means that the listening
mode selected last will be used.
The “
Straight Decode ” option means that straight
decoding listening mode (Dolby Digital, DTS, etc.) is
selected.
■
Subwoofer
`
No , Yes
You can choose whether or not to use the subwoofer
with the sound program.
■
Music Optimizer
*1
`
Off , On
See “Music Optimizer” (
➔
page 58 ).
■
Equalizer
*1
`
Off
`
Manual :
The manual setting in “Equalizer Settings”
(
➔
page 65 ) is applied.
■
Audyssey *1
`
Off , Movie , Music
See “Audyssey” (
➔
page 57 ).
■
Dynamic EQ
*1*2
`
Off , On
See “Dynamic EQ” (
➔
page 57 ).
■
Dynamic Volume
*1*2
`
Off , Light , Medium , Heavy
See “Dynamic Volume” (
➔
page 57 ).
Note
• “ Listening Mode ” is only available when the input signal
matches the setting of “ Sound Program ”.
• You cannot select the “ Subwoofer ” setting if you set it to
“ No ” in “ Speaker Configuration ”.
• “ Music Optimizer ” is only available when “ Stereo
Source 1 ”, “ Stereo Source 2 ” or “ Stereo Source 3 ” is
selected.
• When “ Audyssey Quick Start ” has been used for
measurement, the “ Audyssey ”setting cannot be selected.
*1 This setting cannot be used when the “ Listening Mode ”
setting is set to “ Direct ”.
*2 To enable this setting, you must first perform the Room
Correction and Speaker Setup.
Front left speaker Front right speaker
Listening angle: 30°