Integra DTR-60.5, Инструкция по эксплуатации

Страница: 65 / 112

Advanced Operations
En-65 Operating procedure (
➔
page 59 )
■
Unit
`
feet :
Distances can be set in feet. Range: 0.2ft to
30.0ft in 0.2 foot steps.
`
meters :
Distances can be set in meters. Range: 0.06m
to 9.00m in 0.06 meter steps.
(The default setting varies from country to country.)
■
Left, Front Wide Left, Front High Left, Center,
Front High Right, Front Wide Right, Right,
Surround Right, Surround Back Right, Surround
Back Left, Surround Left, Subwoofer
`
Specify the distance from each speaker to your
listening position.
Note
• Speakers that you set to “ No ” or “ None ” in
“Speaker Configuration” cannot be selected (
➔
page 63 ).
• When the “ Powered Zone 3 ” setting is set to “ Yes ”
(
➔
page 63 ) while Powered Zone 2 is enabled
(
➔
page 83 ), the surround back speakers cannot be used.
• When the “ Speakers Type(Front) ” setting is set to
“ Bi-Amp ” or “ Digital Crossover ” while Powered Zone 2 is
enabled (
➔
page 83 ), the surround back speakers cannot
be used.
Level Calibration
Here you can adjust the level of each speaker with
the built-in test tone so that the volume of each
speaker is the same at the listening position.
■
Left, Front Wide Left, Front High Left, Center
*1
,
Front High Right, Front Wide Right, Right,
Surround Right, Surround Back Right, Surround
Back Left, Surround Left
`
–12.0dB to 0.0dB to +12.0dB in 0.5 dB steps.
■
Subwoofer
*1
`
–15.0dB to 0.0dB to +12.0dB in 0.5 dB steps.
Note
• These settings cannot be calibrated when the AV receiver
is muted.
• Speakers that you set to “ No ” or “ None ” in
“Speaker Configuration” cannot be selected (
➔
page 63 ).
• When the “ Powered Zone 3 ” setting is set to “ Yes ”
(
➔
page 63 ) while Powered Zone 2 is enabled
(
➔
page 83 ), the surround back speakers cannot be used.
• When the “ Speakers Type(Front) ” setting is set to
“ Bi-Amp ” or “ Digital Crossover ” while Powered Zone 2 is
enabled (
➔
page 83 ), the surround back speakers cannot
be used.
• The test tone is output at the standard level for THX, which
is 0 dB (absolute volume setting 82). If you normally listen
at volume settings below this, be careful because the test
tone will be much louder.
*1 For the center speaker and subwoofer, the level settings
made by using the Quick Setup are saved in this menu
(
➔
page 57 ).
Tip
• If you’re using a handheld sound level meter, adjust the level
of each speaker so that it reads 75 dB SPL at the listening
position, measured with C-weighting and slow reading.
Equalizer Settings
With the Equalizer settings, you can adjust the tone of
speakers individually with a 15-band equalizer. The
volume of each speaker can be set.
■
Manual Equalizer
`
On :
You can adjust the equalizer for each speaker
manually. Continue with the following procedure:
`
Off :
Tone off, response flat.
Note
• When the Direct listening mode is selected, the equalizer
settings have no effect.
• If “ Audyssey ” is enabled, it prevails over this setting
(
➔
page 70 ).
THX Audio Setup
■
Surr Back Speaker Spacing
`
<1ft (<0.3m)
`
1ft-4ft (0.3m-1.2m)
`
>4ft (>1.2m)
You can specify the distance between your surround
back speakers.
Note
• Cannot be set if:
– “ Surround Back ” is set to “ None ” (
➔
page 64 ).
This setting is set automatically by
Audyssey MultEQ
® XT32 Room Correction and
Speaker Setup function (
➔
page 26 ).
1
Press w to select “Channel”, and then use
e / r to select a speaker.
2
Use
q
/
w
to select a frequency, and then use
the e / r to adjust the level at that frequency.
The volume at each frequency can be adjusted
from
–6dB to 0dB to +6dB in 1 dB steps.
Tip
• You can select: “ 25Hz ”, “ 40Hz ”, “ 63Hz ”, “ 100Hz ”,
“ 160Hz ”, “ 250Hz ”, “ 400Hz ”, “ 630Hz ”, “ 1kHz ”,
“ 1.6kHz ”, “ 2.5kHz ”, “ 4kHz ”, “ 6.3kHz ”, “ 10kHz ”, or
“ 16kHz ”. And for the subwoofer, “ 25Hz ”, “ 40Hz ”,
“ 63Hz ”, “ 100Hz ”, or “ 160Hz ”.
• Low frequencies (e.g., 25 Hz) affect bass sounds; high
frequencies (e.g., 16 kHz) affect treble sounds.
3
Use q to select “Channel”, and then use e / r
to select another speaker.
Repeat steps 1 and 2 for each speaker.
You cannot select speakers that you set to “
No ”
or “ None ” in the “Speaker Configuration”
(
➔
page 63 ).