11
Front & Rear Panels
—Continued
For detailed information, see the pages in parentheses.
A
COMPONENT VIDEO IN 1, 2, 3 (28, 30, 32)
These component video inputs can be used to con-
nect AV components with component video outputs,
such as DVD players.
B
AM ANTENNA (24)
These push terminals are for connecting an AM
antenna.
C
COMPONENT VIDEO OUT (27)
This component video output can be used to con-
nect a TV or projector with a component video
input.
D
FM ANTENNA (24)
This jack is for connecting an FM antenna.
E
RS232 (38)
This port is for connecting the AV receiver to home
automation equipment and external controllers.
F
12V TRIGGER OUT A/B/C (73, 78)
These jacks can be connected to the 12-volt trigger
inputs on other components. These trigger outputs
can each be assigned to an input so that when that
input is selected, a 12-volt trigger signal is output.
G
IR IN/OUT (78)
These jacks are for connecting the remote sensors
included with multiroom kits (sold separately).
H
A-BUS
A-BUS is a simple, efficient, elegant audio distribu-
tion system. The wiring installation time is signifi-
cantly reduced as only a single CAT-5 wire is run to
each location. A-BUS is easy to use, reliable,
affordable, and most of all, far better sounding than
conventional auto former based volume controls.
ZONE 2 OUT:
Use CAT-5 (eight conductor
twisted) cable to connect directly from the
receiver’s A-BUS RI45 Hub to an A-BUS keypad.
Warning:
DO NOT connect A-BUS output to any computer or
network connections (i.e. ethernet). it will cause
damage to the computer or network components as
24-volt power runs on this same cable to power the
amplifier stages of the amplifier module.
IR OUT:
Another feature of the A-BUS system is
the ability to control source equipment in another
room where the A-BUS module is installed. If you
wish to control another source from the receiver at
the A-BUS keypad by remote control, connect
A-BUS or another brands’s IR emitter on the
receiver’s 40 K terminal. Then place the emitter on
the remote receiver on the front panel.
Typically, the emitter will work when you connect
with a 40 K connector. If it does not work, try a
56 K connector.
DC IN:
Connect A-Bus power supply. Do not use
any other AC Adapter on this connector as it may
cause severe damage to the receiver.
I
MONITOR OUT (27)
The S-Video or composite video jack should be
connected to a video input on your TV or projector.
R
L
R
L
FRONT SPEAKERS
CENTER SPEAKER
R
L
R
L
R
L
SURROUND BACK
SPEAKERS
SURROUND SPEAKERS
IN 1
IN 2
IN 3
FRONT
SURR
CENTER
DVD
CD
VIDEO 3
VIDEO 2
VIDEO 1
VIDEO 3
VIDEO 2
PRE OUT
VIDEO 1
IN
IN
IN
OUT
OUT
IN
IN
OUT
OUT
TAPE
SUB
WOOFER
SUB
WOOFER
MONITOR
OUT
DVD
COMPONENT VIDEO
P
B
Y
P
R
IN
OUT
IN
IN
IN
OUT
REMOTE
CONTROL
ZONE 2
OUT
V
S
ZONE 2 SPEAKERS
IN 1
IN
2
OPTICAL
IN1
IN2
IN3
OUT
COAXIAL
DIGITAL
RS
232
R
L
W
V
U
T
S
R
Q
G
L
N
E
9 J K
1
B C D
M
X Y
6
H
Z
DTR-5.5
DTR-6.5,5.5̲En.book Page 11 Wednesday, July 28, 2004 9:07 AM
