Integra DTR-40.2, Инструкция по эксплуатации

Страница: 50 / 104

50
En
Digital Audio Input
If you connect a component to a digital audio input, you
must assign that input to an input selector. For example, if
you connect your CD player to the
OPTICAL IN 1
, you
must assign “ OPT1 ” to the “ TV/CD ” input selector.
Here are the default assignments.
■
BD/DVD , VCR/DVR , CBL/SAT , GAME , PC , AUX ,
TV/CD , PHONO , PORT

COAX1 , COAX2 , COAX3 , OPT1 , OPT2 :
Select a corresponding digital audio input that the
component has been connected.

- - - - - :
Select if the component is connected to an analog
audio input.
Note
• When an HDMI IN is assigned to an input selector in “HDMI
Input” (
➔
49 ), the same HDMI IN will be set as a priority in this
assignment. In this case, if you want to use the coaxial or optical
audio input, make the selection in the Audio Selector in the
Home menu.
• Available sampling rate for PCM signals from a digital input
(optical and coaxial) is 32/44.1/48/88.2/96 kHz/16, 20, 24 bit.
• If you connect a component (such as UP-A1 Dock that seated
iPod) to the UNIVERSAL PORT jack, you cannot assign any
input to “ PORT ” selector.
Analog Audio Input
Some DVD players output the LFE channel from their
analog subwoofer output at 15 dB higher than normal.
With this setting, you can change the AV receiver’s sub-
woofer sensitivity to match your DVD player.
■
Subwoofer Input Sensitivity

0dB to 15dB in 5 dB step.
Note
• This setting only affects signals connected to the AV receiver’s
multichannel input SUBWOOFER jack.
• If you find that your subwoofer is too loud, try the 10 dB or
15 dB setting.
Main menu Speaker Setup
Here you can check the settings made by
Audyssey MultEQ Room Correction and Speaker Setup
function, or set them manually, which is useful if you
change one of the connected speakers after using
Audyssey MultEQ Room Correction and Speaker Setup
function.
Note
• These settings are disabled when:
– a pair of headphones is connected, or
– the “
Audio TV Out ” setting is set to “ On ” (
➔
61 ) and an
input selector other than HDMI is selected.
Speaker Settings
If the impedance of any speaker is 4 ohms or more but less
than 6, set the minimum speaker impedance to 4 ohms.
If you bi-amp the front speakers, you must change the
“
Speakers Type(Front) ” setting (
➔
50 ).
For hookup information, see “Bi-amping the Front Speak-
ers” (
➔
15 ).
Note
• When bi-amping is used, the AV receiver is able to drive up to
5.1 speakers in the main room.
• Before you change these settings, turn down the volume.
■
Speaker Impedance

4ohms :
Select if the impedance of any speaker is 4 ohms or
more but less than 6.

6ohms :
Select if the impedances of all speakers are between
6 and 16 ohms.
■
Speakers Type(Front)

Normal :
Select this if you’ve connected your front speakers
normally.

Bi-Amp :
Select this if you’ve bi-amped your front speakers.
Note
• Powered Zone 2 cannot be used if “ Speakers Type(Front) ” is
set to “ Bi-Amp ” (
➔
77 ).
■
Powered Zone 2
See “Setting the Powered Zone 2” (
➔
77 ).
Input selector Default assignment
BD/DVD COAX1
VCR/DVR COAX2
CBL/SAT COAX3
GAME OPT1
PC - - - - -
AUX - - - - -
TUNER - - - - - (Fixed)
TV/CD OPT2
PHONO - - - - -
PORT - - - - -
Speaker Setup
Some of the settings in this section are set automatically
by Audyssey MultEQ
® Room Correction and Speaker
Setup function (
➔
28
).
If you change these settings, you must run
Audyssey MultEQ Room Correction and Speaker
Setup again (
➔
28 ).